Алюминий-кремний қоспалары: қасиеттері мен қолданылуы

none

Aluminium–silicon alloys or Silumin is a general name for a group of lightweight, high strength aluminium alloys based on an aluminum–silicon system (AlSi) that consist predominantly of aluminum with silicon as the quantitatively most important alloying element. Pure AlSi alloys cannot be hardened, the commonly used alloys AlSiCu (with copper) and AlSiMg (with magnesium) can be hardened. The hardening mechanism corresponds to that of AlCu and AlMgSi. AlSi alloys are by far the most important of all aluminum cast materials. They are suitable for all casting processes and have excellent casting properties. Important areas of application are in car parts, including engine blocks and pistons. In addition, their use as a functional material for high energy heat storage in electric vehicles is currently being focused on.

Aluminium silicon alloys typically contain 3% to 25% silicon content. Casting is the primary use of aluminum silicon alloys, but they can also be utilized in rapid solidification processes and powder metallurgy. Alloys used by powder metallurgy, rather than casting, may contain even more silicon, up to 50%. Silumin with good castability may give a stronger finished casting than a potentially stronger alloy that is more difficult to cast. Small additions of titanium and boron serve to refine the grain.

Aluminum forms a eutectic with silicon, which is at 577 °C, with a Si content of 12.5% or 12.6%. Up to 1.65% Si can be dissolved in aluminum at this temperature. However, the solubility decreases rapidly with temperature. At 500 °C it is still 0.8% Si, at 400 °C 0.3% Si and at 250 °C only 0.05% Si. At room temperature, silicon is practically insoluble. Aluminum cannot be dissolved in silicon at all, not even at high temperatures. Only in the molten state are both completely soluble. Increases in strength due to solid solution strengthening are negligible. The exact properties depend on whether the composition of the alloy is above, near or below the eutectic point. Castability increases with increasing Si content and is best at about 17% Si; the mechanical properties are best at 6% to 12% Si. The mold filling capacity reaches its maximum at 12% Si, but is also good with other contents. The tendency to form cavities is lowest at 6% to 8% Si and considered low overall. The tendency to hot cracking is low with less than 6% Si. Otherwise, AlSi alloys generally have favorable casting properties: the shrinkage is only 1.25% and the influence of the wall thickness is small. Hypereutectic alloys, with a silicon content of 16 to 19%, such as Alusil, can be used in high wear applications such as pistons, cylinder liners and internal combustion engine blocks. The metal is etched after casting, exposing hard, wear resistant silicon precipitates. The rest of the surface becomes slightly porous and retains oil. Overall this makes for an excellent bearing surface, and at lower cost than traditional bronze bearing bushes.

Hypoeutectic alloys (also hypoeutectic) have a silicon content of less than 12%. With them, the aluminum solidifies first. As the temperature falls and the proportion of solidified aluminum increases, the silicon content of the residual melt increases until the eutectic point is reached. Then the entire residual melt solidifies as a eutectic. The microstructure is consequently characterized by primary aluminium, which is often present in the form of dendrites, and the eutectic of the residual melt lying between them. The lower the silicon content, the larger the dendrites. In pure AlSi alloys, the eutectic is often in a degenerate form. Instead of the fine structure that is otherwise typical of eutectics with its good mechanical properties, AlSi takes the form of a coarse grained structure on slow cooling, in which silicon forms large plates or needles. These can sometimes be seen with the naked eye and make the material brittle. This is not a problem in chill casting, since the cooling rates are high enough to avoid degeneration. In sand casting in particular, with its slow cooling rates, additional elements are added to the melt to prevent degeneration. Sodium, strontium and antimony are suitable. These elements are added to the melt at around 720 °C to 780 °C, causing supercooling that reduces the diffusion of silicon, resulting in a common fine eutectic, resulting in higher strength and elongation at break.

Alloys with 11% Si to 13% Si are counted among the eutectic alloys. Annealing improves elongation and fatigue strength. Solidification is shell forming in untreated alloys and smooth walled in refined alloys, resulting in very good castability. Above all, the flowability and mold filling ability is very good, which is why eutectic alloys are suitable for thin walled parts.

Alloys with more than 13% Si are referred to as over or hypereutectic. The Si content is usually up to 17%, with special piston alloys also over 20%. Hypereutectic alloys have very low thermal expansion and are very wear resistant. In contrast to many other alloys, AlSi alloys do not show their maximum fluidity near the eutectic, but at 14 to 16% Si, in the case of overheating at 17% to 18% Si. The tendency to hot cracking is minimal in the range from 10% to 14%. In the case of hypereutectic alloys, the silicon crystals solidify first in the melt, until the remaining melt solidifies as a eutectic. For grain refinement copper phosphorus alloys are used. The hard and brittle silicon leads to increased tool wear during subsequent machining, which is why diamond tools are sometimes used (See also Machinability).

AlSiMg alloys with small additions of magnesium (below 0.3 to 0.6% Mg) can be hardened both cold and warm. The proportion of magnesium decreases with increasing silicon content, which is between 5% Si and 10% Si. They are related to the AlMgSi alloys: Both are based on the fact that magnesium silicide Mg2Si is precipitated, which is present in the material in the form of finely divided particles and thus increases the strength. In addition, magnesium increases the elongation at break. In contrast to AlSiCu, which can also be hardened, these alloys are corrosion resistant and easy to cast. However, copper is present as an impurity in some AlSiMg alloys, which reduces corrosion resistance. This applies above all to materials that have been melted from secondary aluminium.

AlSiCu alloys are also heat hardenable and additionally high strength, but susceptible to corrosion and less, but still adequately, castable. It is often smelted from secondary aluminium. The hardening is based on the same mechanism as the AlCu alloys. The copper content is 1% to 4%, that of silicon 4% to 10%. Small additions of magnesium improve strength.

4000 series are alloyed with silicon. Variations of aluminium–silicon alloys intended for casting (and therefore not included in 4000 series) are also known as silumin. +4000 series aluminium alloy nominal composition (% weight) and applicationsAlloyAl contentsAlloying elementsUses and refs400698.3Si 1.0; Fe 0.65Work hardened or aged400796.3Si 1.4; Mn 1.2; Fe 0.7; Ni 0.3; Cr 0.1Work hardened401596.8Si 2.0; Mn 1.0; Mg 0.2Work hardened403285Si 12.2; Cu 0.9; Mg 1; Ni 0.9;Forgings404394.8Si 5.2Rod404785.5Si 12.0; Fe 0.8; Cu 0.3; Zn 0.2; Mn 0.15; Mg 0.1Sheet, cladding, fillers454393.7Si 6.0; Mg 0.3architectural extrusions

Within the Aluminum Association numeric designation system, Silumin corresponds to alloys of two systems: 3xxx, aluminum–silicon alloys also containing magnesium and/or copper, and 4xx. x, binary aluminum–silicon alloys. Copper increases strength, but reduces corrosion resistance. AlSi eutectic casting alloys are used for machine parts, cylinder heads, cylinder crankcases, impellers and ribbed bodies. Hypereutectic (high silicon) alloys are used for engine parts because of low thermal expansion and high strength and wear resistance. This also includes special piston alloys with around 25% Si. Alloys with additions of magnesium (AlSiMg) can be hardened by heat treatment. An example use case are wheel rims produced by low pressure casting because of their good strength, corrosion resistance and elongation at break. Alloys with about 10% Si are used for cylinder heads, switch housings, intake manifolds, transformer tanks, wheel suspensions and oil pans. Alloys with 5% Si to 7% Si are used for chassis parts and wheels. At levels of 9%, they are suitable for structural components and body nodes. The copper containing AlSiCu alloys are used for gear housings, crankcases and cylinder heads because of their heat resistance and hardenability. In addition to the use of AlSi alloys as a structural material, in which the mechanical properties are paramount, another area of application is latent heat storage. In the phase change of the alloy at 577 °C, thermal energy can be stored in the form of the enthalpy of fusion. AlSi can therefore also be used as a metallic phase change material (mPCM) be used. Compared to other phase change materials, metals are characterized by a high specific energy density combined with high thermal conductivity. The latter is important for the rapid entry and exit of heat in the storage material and thus increases the performance of a heat storage system. These advantageous properties of mPCM such as AlSi are of particular importance for vehicle applications, since low masses and volumes as well as high thermal performance are the main goals here. By using storage systems based on mPCM, the range of electric cars can be increased by thermally storing the necessary thermal energy for heating in the mPCM instead of taking it from the traction battery. Almost eutectic AlSi melts are also used for hot dip aluminizing. In the process of continuous strip galvanizing, steel strips are finished with a heat resistant metallic coating 10 25 μm thick. Hot dip aluminized sheet steel is an inexpensive material for thermally stressed components. Unlike zinc coatings, the coating does not provide cathodic protection under atmospheric conditions.

High castability, fluidity, corrosion resistance, ductility, and low density. Usable for large castings, which can operate under heavy load conditions. Considered to not be a heat treatable alloy, but the addition of Mg & Cu can allow it to be heat treated, e. g. AΠ4 alloys. Strengthened by solution treatment, e. g. adding 0.01% sodium (in the form of sodium fluoride [NaF] and sodium chloride [NaCl]) to the melt just before casting. A disadvantage is a tendency for porosity in the casting, i. e. the casting can become foam like. This can be avoided by casting under pressure in autoclaves.