Екі бағытта жүргізілетін пойыз конфигурациясы

Train able to be operated by a driver at either end

Push–pull is a configuration for locomotive hauled trains, allowing them to be driven from either end of the train, whether having a locomotive at each end or not. A push–pull train has a locomotive at one end of the train, connected via some form of remote control, such as multiple unit train control, to a vehicle equipped with a control cab at the other end of the train. This second vehicle may be another locomotive, or an unpowered control car. In the UK and some other parts of Europe, the control car is referred to as a driving trailer (or driving van trailer/DVT where there is no passenger accommodation); in the US and Canada, they are called cab cars.

Historically, push–pull trains with steam power provided the driver with basic controls at the cab end along with a bell or other signalling code system to communicate with the fireman located in the engine itself in order to pass commands to adjust controls not available in the cab. At low speeds, some push–pull trains are run entirely from the engine with the guard operating bell codes and brakes from the leading cab when the locomotive is pushing the train. Many mountain railways also operate on similar principles in order to keep the locomotive lower down than the carriage to prevent any opportunity for a carriage to run away from a train down the gradient and also so that even if the locomotive ever ran away, it would not take the carriage with it. Modern train control systems use sophisticated electronics to allow full remote control of locomotives. Nevertheless, push–pull operation still requires considerable design care to ensure that control system failure does not endanger passengers and also to ensure that in the event of a derailment, the pushing locomotive does not push a derailed train into an obstacle, worsening the accident. The 1984 Polmont rail accident, in Scotland, occurred when a push–pull train struck a cow on the track. When operating push–pull, the train can be driven from either the locomotive or the alternative cab. If the train is heading in the direction in which the locomotive end of the train is facing, this is considered 'pulling'. If the train is heading in the opposite direction, this is considered 'pushing' and the motorman or engine driver is located in the alternative cab. This configuration means that the locomotive never needs to be uncoupled from the train and ensures fast turnaround times at a railway station terminus.

Alternatively, a push–pull train, especially a long one, may have a locomotive on each end so that there is always one locomotive pushing and one locomotive pulling. In this case, caution must be used to make sure that the two locomotives do not put too much stress on the cars from uneven locomotives. It is usual to arrange matters so that the trailing locomotive supplies less power, i. e. that the locomotive at the front does more pulling than the locomotive at the rear does pushing. Having an independent locomotive, as opposed to a power car at each end, is also known in the railway world as a top and tail. When this configuration is used in the US, only one locomotive (usually the front locomotive) is allowed to provide head end power (HEP: electricity supply for heating, air conditioning and lighting) to the train. The two locomotive formation is used by the InterCity 125; its Australian equivalent, the XPT; Brightline; Amtrak's Acela; SNCF's TGV; Taiwan Railways Administration's E1000 series; and New Jersey Transit's longest Northeast Corridor Line multilevel trains. This form of operation has not necessarily been a function of train length; sometimes it was the most convenient way to set up push–pull operation in pre HEP days without converting coaches to cab control operation. A prime example of this was the Reading Company which converted its small fleet of streamstyled heavyweight medium distance coaches for its non electric commuter operation, with a pair of EMD FP7 diesels bracketing a single five car train, to supplant the Reading's fleet of RDCs. This train normally operated a weekday peak hour round trip between Reading Terminal, Philadelphia and Reading, Pennsylvania, from the late 1960s until 1981, with operation in the last five years by Conrail under contract to SEPTA.

A rare but possible configuration has a locomotive in the middle of the train with control cars at both ends, as was, for instance, used for a time on the Brussels–Amsterdam Benelux train when there were control cars but no three voltage (3 kV DC, 1.5 kV DC, 25 kV 50 Hz) locomotives supporting the ERTMS train control system in use on the Belgian HSL 4 and the Dutch HSL Zuid. The Class 28 TRAXX locomotives were later upgraded, and the service went back to "normal" push–pull operation.

In this configuration, locomotives hauling a train are located other than at the front or the back. It may include remote control locomotives in the middle of a train. If operational considerations or economics require, trains can be made longer if intermediate locomotives are inserted in the train and are remotely controlled from the leading locomotive.

In 1988, 52 Mark 3 Driving Van Trailers were built by British Rail Engineering Limited to allow it to replace life expired electric locomotives on the West Coast Main Line. These operated with Mark 2 and Mark 3 sets. As part of the electrification of the East Coast Main Line, 31 Mark 4 Driving Van Trailers were built in the late 1980s by Metro Cammell to operate with Mark 4s coaches at the south end of the InterCity 225 sets. Some of these passed to Transport for Wales Rail in 2021 to work on their Holyhead to Cardiff Premier Service. In the 2000s, some Mark 3s have been modified to operate with Class 67 locomotives with Arriva Trains Wales, Chiltern Railways and Wrexham & Shropshire. In 2019, new Mark 5 carriages, one of which has a cab, entered service with Class 68 locomotives for TransPennine Express, in a push–pull configuration.

Córas Iompair Éireann's first push–pull trains were conversions of their 2600 Class DMUs (Park Royal body, AEC motors) running with the long withdrawn 201 Class Metropolitan Vickers Bo Bo diesels re engined with EMD 567 prime movers; the cars were subsequently renumbered in the 6100 series (Driving van trailers), 6200 series (trailer with "blind" cab end) and 6300 series (double gangway intermediate car). In push–pull formation, they operated Dublin Suburban Rail services from 1971 until the inauguration of the DART EMU service in July 1984. The remaining push–pull trains operated on Dublin Maynooth commuter services until they were supplanted by Cravens, and later by the modern 2600 Class DMUs. Iarnród Éireann employs push–pull trains of two different kinds. The first of these were built in 1996. These are De Dietrich Ferroviaire–built Enterprise push–pull sets, jointly owned with Northern Ireland Railways for operation on the Dublin to Belfast route. These are powered by 201 Class locomotives. The other type of push–pull train used in Ireland is the Mark 4 type (not to be confused with the British Rail Mark 4 type). These sets, delivered in 2005–2006, are used exclusively on the Dublin to Cork route, again operated by 201 Class locomotives. Between 1980 and 2009, Iarnród Éireann operated push–pull sets based on the British Rail Mark 3 design, with a non gangwayed driving cab fitted. These were operated with 201 Class locomotives, although in the past 121 Class locomotives were also used. It remains unknown whether these sets were ever hauled as normal coaching stock by non–push–pull fitted locomotives. The sets originally operated in the Dublin outer suburban area and on the Limerick to Limerick Junction shuttle, but were gradually moved to mainline InterCity routes out of Dublin Heuston after the introduction of railcar sets elsewhere. The entire Mark 3 fleet was withdrawn in September 2009 and scrapped in 2014.

In June 1958, SNCF commenced operating steam trains in push–pull formation out of Gare de l'Est.

The first major application of push–pull operation using the modern single diesel configuration was on the Chicago & Northwestern Railroad, announced in 1958. In 1959, the C&NW received its first Control Cab equipped Bilevel rail cars for commuter use. The extreme efficiency and success of these trains is why almost all of the commuter rail services in the United States and Canada utilize 100% push–pull operation on their locomotive hauled trains. Examples include: Chicago (Metra); New York City (Metro North, the Long Island Rail Road and New Jersey Transit); Philadelphia (SEPTA); the Washington, DC and Baltimore area (MARC and VRE); Boston (MBTA); Dallas Fort Worth metroplex (Trinity Railway Express); the Greater Miami area (Tri Rail); the San Francisco Bay Area (Caltrain and ACE); Southern California (Metrolink and Coaster); Toronto (GO Transit); Montreal (AMT); and the Wasatch Front in Utah (UTA FrontRunner). Most of these systems (except for SEPTA and Metro North) continue to utilize some type of bi level passenger cars for push–pull service, either partially or exclusively. Amtrak has a number of converted Metroliner EMUs in service as cab cars on the Keystone Corridor, where they operate in conjunction with ACS 64 electric locomotives. In addition, many regional services, such as the Michigan Services, Downeaster, and Cascades, are operated with Non Powered Control Units – EMD F40PH locomotives converted to use as a cab control and baggage car, earning itself the nickname 'cabbage cars'. Similarly, the Capitol Corridor, San Joaquin, and Pacific Surfliner services in California are operated in push–pull configuration using purpose built cab cars and diesel locomotives. The Muskingum Electric Railroad was a private, coal hauling railway in central Ohio that ran for more than 20 years with two driverless General Electric E50C electric locomotives that ran backwards from the coal fired powerplant they served to the mine where their trains were loaded by affixing bogie trucks, a headlight, and a horn to the last freight car on each train.

In 1996, Israel Railways began running GEC Alstom push–pull coaches. Since then, it has also acquired push–pull coaches from Bombardier and Siemens. As of 2016, the bulk of Israel Railways' passenger operations use push–pull coaches. All of them have one locomotive at one end and a control car at the other end.

The New South Wales XPT long distance passenger trains used by NSW TrainLink operate in a push–pull operation. In the past V/Line operated P class push–pulls on interurban services to Bacchus Marsh and Wyndham Vale until 2017. South Australian Railways' 2000 class DMUs could be found with at least one motor car and one cab car in a push–pull configuration until their withdrawal in 2016.

In the first quarter of the 20th century up to 13 motor trains ran on NZR. Until 2015, the Auckland suburban network run by Transdev used rebuilt British Rail Mark 2 carriages in either four, five or six car configurations. Three to five SA class carriages and an SD class driving carriage, fitted with a cab, were coupled to a DC class (4 and 5 car) or DFT/DFB class (6 car) locomotive, leased from KiwiRail. All SA and SD class cars were rebuilt by Hillside Workshops. Auckland also operated former Queensland Rail SX carriages in push–pull mode with two DBR class locomotives. Following electrification of most of the Auckland suburban railway network, these diesel units have been replaced by a modern electrical fleet that consist of one or two sets of 3 car units (each of which have one carriage that can service passengers with disabilities).