Ағылшыншамен салыстырыңыз: абзацты басыңыз — түпнұсқа терезеде ашылады. Абзац астындағы EN түймесі оны мәтін ішінде көрсетеді.
Мазмұны
Кіріспе
UTRAN компоненті GSM иерархиясындағы базалық станция контроллеріне ұқсас. Радио желі контроллері (RNC) UMTS радио қолжетімділік желісінің (UTRAN) басқарушы элементі болып табылады және оған қосылған Node B-лерді басқаруға жауапты. RNC радио ресурстарын басқаруды, қозғалмалылық басқару функцияларының бір бөлігін жүзеге асырады және пайдаланушы деректері ұялы телефонға жіберілу және одан алыну алдында шифрлану орындалатын нүкте болып табылады. RNC Media Gateway (MGW) арқылы контурлы коммутациялық ядролық желіге және пакеттік коммутациялық ядролық желідегі SGSN (Serving GPRS Support Node) құрылғысына қосылады.
UTRAN component similar to a base station controller in GSM hierarchy
The Radio Network Controller (RNC) is a governing element in the UMTS radio access network (UTRAN) and is responsible for controlling the Node Bs that are connected to it. The RNC carries out radio resource management, some of the mobility management functions and is the point where encryption is done before user data is sent to and from the mobile. The RNC connects to the Circuit Switched Core Network through Media Gateway (MGW) and to the SGSN (Serving GPRS Support Node) in the Packet Switched Core Network.
Интерфейстер
Желі элементтері арасындағы логикалық байланыстар интерфейстер деп аталады. RNC мен контурлы коммутацияланған негізгі желі (CS CN) арасындағы интерфейс Iu CS, ал RNC мен пакеттік коммутацияланған негізгі желі арасындағы интерфейс Iu PS деп аталады. Басқа интерфейстерге Iub (RNC мен Node B арасындағы) және Iur (бір желідегі RNC арасындағы) жатады. Iu интерфейстері пайдаланушы трафигін (дауыс немесе деректер сияқты) және басқару ақпаратын (қараңыз) жеткізеді, ал Iur интерфейсі екі RNC қатысатын жұмсақ тапсырулар үшін негізінен қажет, бірақ міндетті емес, себебі Iur болмаған жағдайда осы тапсырулар қатты тапсыруларға айналады. 3GPP R4 дейін UTRAN-дағы барлық интерфейстер ATM арқылы іске асырылды, WCDMA технологиясын пайдаланатын Uu (радио интерфейсі) ерекшелік. R5 нұсқасынан бастап IP тасымалдаушыларын Ethernet арқылы пайдалануға болады. Физикалық жағынан, бұл интерфейстер SDH арқылы оптикалық талшықтан, E1 (кейде PDH деп аталады) мыс сымынан немесе микротолқындық радиобайланыс арқылы жеткізілуі мүмкін. Бірнеше E1 интерфейсін біріктіріп IMA тобын құруға болады. Интерфейстер логикалық болғандықтан, көптеген интерфейстерді бір тарату желісіне мультиплекстеуге болады. Нақты іске асыру желі топологиясына байланысты, мысалы: тізбектік, алыс жұлдызды, торлы және сақина тәрізді конфигурациялар.
The logical connections between the network elements are known as interfaces. The interface between the RNC and the Circuit Switched Core Network (CS CN) is called Iu CS and between the RNC and the Packet Switched Core Network is called Iu PS. Other interfaces include Iub (between the RNC and the Node B) and Iur (between RNCs in the same network). Iu interfaces carry user traffic (such as voice or data) as well as control information (see ), and Iur interface is mainly needed for soft handovers involving 2 RNCs though not required as the absence of Iur will cause these handovers to become hard handovers. Until 3gpp R4, all the interfaces in the UTRAN are implemented using ATM only, except the Uu (air) interface which uses WCDMA technology. Starting R5, IP bearers can be used over Ethernet instead. Physically, these interfaces can be carried over SDH over optical fiber, E1 (sometimes referred to as PDH) over a copper wire or microwave radio. Several E1s can be bundled to form an IMA Group. Since the interfaces are logical, many interfaces can be multiplexed onto the same transmission line. The actual implementation depends on the network topology; examples are chain, distant star, mesh and loop configurations.
Хаттамалар
Iub, Iu және Iur протоколдарының барлығы пайдаланушы деректері мен сигналдауды (яғни, басқару жазығын) жеткізеді. RNC-нің Node B-ны басқаруына жауапты сигналдау протоколы NBAP (Node B Application Part) деп аталады. NBAP жалпы және арнайы NBAP (C NBAP және D NBAP) болып бөлінеді, мұнда жалпы NBAP Node B-ның жалпы функционалдығын басқарады, ал арнайы NBAP Node B-ның жеке ұяшықтарын немесе секторларын басқарады. NBAP Iub арқылы жеткізіледі. NBAP ортақ және арнайы процедураларды өңдеу үшін NodeB бақылау порты (NCP) – ортақ NBAP процедураларын өңдейтін, және байланыс бақылау порты (CCP) – арнайы NBAP процедураларын өңдейтін болып бөлінеді. Транспорттық қабаттың басқару жазығы протоколы ALCAP (Access Link Control Application Protocol) деп аталады. ALCAP-тың негізгі функциясы – арна идентификаторларын (CID) пайдаланып, әртүрлі пайдаланушыларды бір AAL2 беру жолына мультиплекстеу. ALCAP Iub және Iu CS интерфейстері арқылы жеткізіледі. RNC мен ядролық желі арасындағы байланысқа жауапты сигналдау протоколы RANAP (Radio Access Network Application Part) деп аталады және Iu интерфейсі арқылы жеткізіледі. RNC-лер арасындағы байланысқа жауапты сигналдау протоколы RNSAP (Radio Network Subsystem Application Part) деп аталады және Iur интерфейсінде жүзеге асырылады.
Iub, Iu and Iur protocols all carry both user data and signalling (that is, control plane). Signalling protocol responsible for the control of the Node B by the RNC is called NBAP (Node B Application Part). NBAP is subdivided into Common and Dedicated NBAP (C NBAP and D NBAP), where Common NBAP controls overall Node B functionality and Dedicated NBAP controls separate cells or sectors of the Node B. NBAP is carried over Iub. In order for NBAP to handle common and dedicated procedures, it is divided into: NodeB Control Port (NCP) which handles common NBAP procedures and Communication Control Port (CCP) which handles dedicated NBAP procedures. Control plane protocol for the transport layer is called ALCAP (Access Link Control Application Protocol). Basic functionality of ALCAP is multiplexing of different users onto one AAL2 transmission path using channel IDs (CIDs). ALCAP is carried over Iub and Iu CS interfaces. Signalling protocol responsible for communication between RNC and the core network is called RANAP (Radio Access Network Application Part), and is carried over Iu interface. Signalling protocol responsible for communications between RNCs is called RNSAP (Radio Network Subsystem Application Part) and is carried on the Iur interface.