Ағылшыншамен салыстырыңыз: абзацты басыңыз — түпнұсқа терезеде ашылады. Абзац астындағы EN түймесі оны мәтін ішінде көрсетеді.
Кіріспе
Мұнай өндірісінде корпус ілгіші – ұңғыма басы құралымдарының бір бөлігі болып табылады, ол ұңғымаға түсірілгенде корпус тізбегін қолдайды. Ол корпустың дұрыс орналасуын қамтамасыз етеді. Корпус тізбегі ұңғымаға түсірілгеннен кейін, ол корпус ілгішімен ілініп, ілгіштің тіреуіне орналасады. Корпус ілгіштері корпустың толық салмағын көтеруге және ілгіш пен катушка арасында герметикалық тығыздауды қамтамасыз етуге арналған. Корпус ілгіштері ұңғыма ошағының радиалды деформациясы арқылы, мысалы, "Pos Grip" әдісімен ұңғыма ошағының ішінде де орнатылуы мүмкін. Бұл ұңғымадағы жеке корпус тізбектерін қолдау үшін жасалған. Бұл – қону базасы немесе корпус басы. Ол әдетте жер беткі корпус тізбегінің үстіне дәнекерленеді немесе бұралады. Жер беткі корпус ұңғыманың негізі ретінде қызмет етеді және аспалы жүктемені жерге ауыстырады. Корпус басы ыдыс тәрізді дайындалады, оған құлаптар орнатылып, корпусты бекітеді. Көптеген корпус басдары аннулустағы қысымды өлшеуге және қажет болған жағдайда соруға немесе сорғылауға мүмкіндік береді. Корпус тізбегінің және аннулустың жоғарғы бөлігі әдетте жабылады. 2014 жылы әлем бойынша 155 000-нан астам мұндай құрылғы орнатылған, бұл ең көп таралған корпус ілгішінің көлемі болып табылады. 2015 жылы мұнай өнеркәсібінің қысқаруына байланысты бұл көрсеткіш шамамен 120 000 бірлікке дейін төмендеді, оның ішінде 36 822 "Pos Grip" корпус ілгіштері болды. Аралық немесе қорғаныш корпусы бір немесе бірнеше тізбектен тұруы мүмкін. Қорғаныш корпусы көбінесе ұңғыманы тереңдеу үшін қажетті саз салмағына байланысты орнатылады. Аралық тізбектердің кең таралған өлшемдері (немесе терең ұңғымаларда одан да үлкен) құрайды. Әрбір тізбек цементпен бекітіледі. Әрине, егер ұңғымада бірнеше аралық корпус тізбегі қажет болса, жер беткі тесіктің диаметрі барлық қажетті тізбектерді қабылдауға жеткілікті болуы керек. Ұңғымалар төменнен жоғарыға қарай жоспарланады. Ұңғыманың мақсаты ұңғыманың түбінің диаметрін анықтайды. Егер ұңғыма теңіздегі барлаушы ұңғыма болса, онда оның түбі ағаш кесуші зондты орналастыру үшін ғана жеткілікті болуы керек. Егер ұңғыма өте өнімді болса, үлкен диаметрлі корпуста өндіріс құбыры орнатылуы мүмкін. Газ ұңғымаларына тек кішкентай құбырлар қажет болуы мүмкін, сондықтан тесік салыстырмалы түрде кішкентай болуы мүмкін. Геологиялық алаптарда кеңінен зерттелмеген жаңа ұңғымаларда алғашқы тесіктер бірнеше резервтік корпус тізбегін қамтамасыз етуге жеткілікті болуы мүмкін.
In petroleum production, the casing hanger is that portion of a wellhead assembly which provides support for the casing string when it is lowered into the wellbore. It serves to ensure that the casing is properly located. When the casing string has been run into the wellbore it is hung off, or suspended, by a casing hanger, which rests on a landing shoulder inside the casing spool. Casing hangers must be designed to take the full weight of the casing, and provide a seal between the casing hanger and the spool. Casing Hangers may also be suspended within the wellhead by means of radial distortion of the wellhead bore e. g. the "Pos Grip" method. This is installed to support the individual casing strings in the well. It is the landing base or the casing head. This is usually welded or screwed to the top of the surface casing string. The surface casing serves as a foundation pile for the well which transfers the hanging load to the earth. The casing head is prepared with a bowl into which the slips sit and chuck the casing in place. Most casing heads allow for the pressure readings to be taken on the annulus and provide the means to pump out or into if necessary. The top of the casing string and annulus is usually sealed. The most common size of casing hanger is with over 155,000 such units installed worldwide in 2014 alone. The contraction of the oilfield industry throughout 2015 meant that this figure was reduced somewhat to just under 120,000 units, of which 36,822 were "Pos Grip" casing hangers. Intermediate, or protective, casing may be one or more strings of casing. Protective casing is most frequently installed in a well because of the mud weight required to drill deeper in the well. Common sizes of intermediate strings range from to (or larger in deep wells). Each string is cemented in place. Obviously, if several strings of intermediate casing are required in a well, the diameter of the surface hole must be large enough to permit all of the necessary strings. Wells are planned from the bottom up. The purpose of the well determines the diameter of the bottom of the well. If the well is an exploratory wild cat offshore, the bottom of the well must be only large enough to accommodate a logging sonde. If the well is a very productive oil well, a production tubing might be installed in a larger diameter casing. Gas wells may only require a small tubing set in casing, so the hole might be relatively small. With rank wildcats in geological basins that have not been explored extensively, the first holes might be large enough to provide for a couple of contingency strings of casing.