Ақауларды талдау процесі және себептерін анықтау

Process of collecting and analyzing data to determine the cause of a failure
Failure analysis is the process of collecting and analyzing data to determine the cause of a failure, often with the goal of determining corrective actions or liability. According to Bloch and Geitner, ”machinery failures reveal a reaction chain of cause and effect usually a deficiency commonly referred to as the symptom ”. Failure analysis can save money, lives, and resources if done correctly and acted upon. It is an important discipline in many branches of manufacturing industry, such as the electronics industry, where it is a vital tool used in the development of new products and for the improvement of existing products. The failure analysis process relies on collecting failed components for subsequent examination of the cause or causes of failure using a wide array of methods, especially microscopy and spectroscopy. Nondestructive testing (NDT) methods (such as industrial computed tomography scanning) are valuable because the failed products are unaffected by analysis, so inspection sometimes starts using these methods.

Forensic inquiry into the failed process or product is the starting point of failure analysis. Such inquiry is conducted using scientific analytical methods such as electrical and mechanical measurements, or by analyzing failure data such as product reject reports or examples of previous failures of the same kind. The methods of forensic engineering are especially valuable in tracing product defects and flaws. They may include fatigue cracks, brittle cracks produced by stress corrosion cracking or environmental stress cracking for example. Witness statements can be valuable for reconstructing the likely sequence of events and hence the chain of cause and effect. Human factors can also be assessed when the cause of the failure is determined. There are several useful methods to prevent product failures occurring in the first place, including failure mode and effects analysis (FMEA) and fault tree analysis (FTA), methods which can be used during prototyping to analyze failures before a product is marketed. Several of the techniques used in failure analysis are also used in the analysis of no fault found (NFF) which is a term used in the field of maintenance to describe a situation where an originally reported mode of failure can't be duplicated by the evaluating technician and therefore the potential defect can't be fixed. NFF can be attributed to oxidation, defective connections of electrical components, temporary shorts or opens in the circuits, software bugs, temporary environmental factors, but also to the operator error. A large number of devices that are reported as NFF during the first troubleshooting session often return to the failure analysis lab with the same NFF symptoms or a permanent mode of failure. The term failure analysis also applies to other fields such as business management and military strategy.

A failure analysis engineer often plays a lead role in the analysis of failures, whether a component or product fails in service or if failure occurs in manufacturing or during production processing. In any case, one must determine the cause of failure to prevent future occurrence, and/or to improve the performance of the device, component or structure. Structural Engineers and Mechanical Engineers are very common for the job. More specific majors can also get into the position such as materials engineers. Specializing in metallurgy and chemistry is always useful along with properties and strengths of materials. Someone could be hired for different reasons, whether it be to further prevent or liability issues. The median salary of a failure analysis engineer, an engineer with experience in the field, is $81,647. A failure analysis engineer requires a good amount of communication and ability to work with others. Usually, the person hired has a bachelor's degree in engineering, but there are certifications that can be acquired. Mr. Aguilar is the Branch Chief for Caltrans Structural Materials Testing Branch with 30 years’ experience as an engineer. Others said more prevention could have been done. Priestly said that “neither of the department’s projects to strengthen roadways addressed the problems of weakness ” in the bridge's joints. Some experts agreed that more could have been done to prevent this disaster. The program is under fire for making “the failure more serious”.]] A product needs to be able to work even in the hardest of scenarios. This is very important on products made for expensive builds such as buildings or aircraft. If these parts fail, they can cause serious damage and/or safety problems. A product starts to be designed " to minimize the hazards associated with this "worst case scenario." Discerning the worst case scenario requires a complete understanding of the product, its loading and its service environment. Prior to the product entering service, a prototype will often undergo laboratory testing which proves the product withstands the worst case scenario as expected." Some of the tests done on jet engines today are very intensive checking if the engine can withstand:

ingestion of debris, dust, sand, etc. ;
ingestion of hail, snow, ice, etc. ;
ingestion of excessive amounts of water. These tests must be harder than what the product will experience in use. The engines are pushed to the max in order to ensure that the product will function the way it should no matter the condition. Failure analysis on both sides is about the prevention of damage and maintaining safety.