Ағылшыншамен салыстырыңыз: абзацты басыңыз — түпнұсқа терезеде ашылады. Абзац астындағы EN түймесі оны мәтін ішінде көрсетеді.
Кіріспе
Кесу интерферометрі - бұл кедергілерді байқаудың және осы құбылысты, әсіресе, когеренттік ұзындығы, әдетте, кесу пластинасының қалыңдығынан әлдеқайда ұзын лазерлік көздерден келетін жарық сәулелерінің коллимациясын сынау үшін пайдаланудың өте қарапайым құралы (графиканы қараңыз), сондықтан кедергілердің негізгі шарты орындалады.
The shearing interferometer is an extremely simple means to observe interference and to use this phenomenon to test the collimation of light beams, especially from laser sources which have a coherence length which is usually significantly longer than the thickness of the shear plate (see graphics) so that the basic condition for interference is fulfilled.
Функция
Сынау құрылғысы N BK7 секілді жоғары сапалы оптикалық шыныдан тұрады, өте жазық оптикалық беттері, әдетте, бір-біріне сәл бұрышта орналасқан. Жазық толқын 45° бұрышта соққы бергенде, ол ең жоғары сезімталдықты береді, ол екі рет шағылады. Екі шағылысу пластинаның шекті қалыңдығы мен кене арқылы бүйірінен бөлінеді. Бұл бөлінуді қиып алу деп атайды және аспапқа өз атын берді. Қиюды торлар арқылы да жасауға болады. Кейде параллель бүйірлі қима тақталары қолданылады, бірақ тіктелген тақталардың кедергілік жиектерін түсіндіру салыстырмалы түрде оңай және қарапайым. Қиыршықтай қиғаш пластиналар алдыңғы және артқы беттің шағылысуы арасындағы сыныпталған жол айырмашылығын тудырады; нәтижесінде жарықтың параллель сәулесі жапсарлас шегі ішінде сызықтық жиектік үлгі жасайды. Жазық толқын маңы оқиғасы кезінде екі шағылысқан сәулелердің бір-біріне ауысуы интерференциялық жиектерді көрсетеді, мұндағы арақашықтық қисаюға перпендикуляр, сәуле толқын ұзындығы, n сыну индексі және кене бұрышы. Бұл теңдеу кесілген қима табанынан бақылау жазықтығына дейінгі арақашықтық бақылау жазықтығындағы толқын маңының қисықтық радиусына қатысты кіші екенін жеңілдетеді. Шеңберлер бірдей арақашықтықта және кене бағытына дәл тік және қиып-тарту интерферометріне сәуле осі бойымен тураланған, әдеттегі сым курсорына параллель болады. Шеңберлердің бағыты сәуле торы толықтай біріктірілмеген кезде өзгереді. Кесінді қима табанында коллиматтанбаған сәуле түсуі жағдайында екі шағылысқан толқын маңы арасындағы жол айырмасы қисықтың белгісіне байланысты толық коллиматтанған жағдайда көбейтіледі немесе азаяды. Содан кейін үлгіні айналдырады және сәуле толқын маңының қисықтық радиусын есептеуге болады: , қисайту қашықтығы, жиек қашықтығы, толқын ұзындығы және жиектің туралауының бұрыштық ауытқуы. Егер оның орнына шетке дейінгі нормальды арақашықтық қолданылса, бұл теңдеу , мұндағы шетке дейінгі нормальды арақашықтық.
The testing device consists of a high quality optical glass, like N BK7, with extremely flat optical surfaces that are usually at a slight angle to each other. When a plane wave is incident at an angle of 45°, which gives maximum sensitivity, it is reflected two times. The two reflections are laterally separated due to the finite thickness of the plate and by the wedge. This separation is referred to as the shear and has given the instrument its name. The shear can also be produced by gratings. Parallel sided shear plates are sometimes used, but the interpretation of the interference fringes of wedged plates is relatively easy and straightforward. Wedged shear plates produce a graded path difference between the front and back surface reflections; as a consequence, a parallel beam of light produces a linear fringe pattern within the overlap. With a plane wavefront incident, the overlap of the two reflected beams shows interference fringes with a spacing of , where is the spacing perpendicular to shear, is the wavelength of the beam, n the refractive index, and the wedge angle. This equation makes the simplification that the distance from the wedged shear plate to the observation plane is small relative to the wavefront radius of curvature at the observation plane. The fringes are equally spaced and will be exactly perpendicular to the wedge orientation and parallel to a usually present wire cursor aligned along the beam axis in the shearing interferometer. The orientation of the fringes varies when the beam is not perfectly collimated. In the case of a noncollimated beam incident on a wedged shear plate, the path difference between the two reflected wavefronts is increased or decreased from the case of perfect collimation depending on the sign of the curvature. The pattern is then rotated and the beam's wavefront radius of curvature can be calculated: , with the shear distance, the fringe distance, the wavelength and the angular deviation of the fringe alignment from that of perfect collimation. If the spacing normal to the fringes is used instead, this equation becomes , where is the fringe spacing normal to the fringes.