IBM BladeCenter серверлік архитектурасы

Blade server architecture by IBM

The IBM BladeCenter was IBM's blade server architecture, until it was replaced by Flex System in 2012. The x86 division was later sold to Lenovo in 2014.

Introduced in 2002, based on engineering work started in 1999, the IBM eServer BladeCenter was relatively late to the blade server market. It differed from prior offerings in that it offered a range of x86 Intel server processors and input/output (I/O) options. The naming was changed to IBM BladeCenter in 2005. In February 2006, IBM introduced the BladeCenter H with switch capabilities for 10 Gigabit Ethernet and InfiniBand 4X. A web site called Blade. org was available for the blade computing community through about 2009. In 2012, the replacement Flex System was introduced.

BladeCenter T is the telecommunications company version of the original BladeCenter, available with either AC or DC (48 V) power. Has 8 blade slots in 8U, but uses the same switches and blades as the regular BladeCenter E. To keep NEBS Level 3 / ETSI compliant special Network Equipment Building System (NEBS) compliant blades are available.

BladeCenter HT is the telecommunications company version of the BladeCenter H, available with either AC or DC (48 V) power. Has 12 blade slots in 12U, but uses the same switches and blades as the regular BladeCenter H. But to keep NEBS Level 3 / ETSI compliant special NEBS compliant blades are available.

Modules based on x86 processors from Intel.

Modules based on x86 processors from AMD.

Modules based on PowerPC or Power ISA based processors from IBM.

The BladeCenter can have a total of four switch modules, but two of the switch module bays can take only an Ethernet switch or Ethernet pass though. To use the other switch module bays, a daughtercard needs to be installed on each blade that needs it, to provide the required SAN, Ethernet, InfiniBand or Myrinet function. Mixing of different type daughtercards in the same BladeCenter chassis is not allowed.

Gigabit Ethernet switch modules were produced by IBM, Nortel, and Cisco Systems. BLADE Network Technologies produced some switches, and later was purchased by IBM. In all cases speed internal to the BladeCenter, between the blades, is non blocking. External Gigabit Ethernet ports vary from four to six and can be either copper or optical fiber.

A variety of SAN switch modules have been produced by QLogic, Cisco, McData (acquired by Brocade) and Brocade ranging in speeds of 1, 2, 4 and 8 Gbit Fibre Channel. Speed from the SAN switch to the blade is determined by the lowest common denominator between the blade HBA daughtercard and the SAN switch. External port counts vary from two to six, depending on the switch module.

A InfiniBand switch module has been produced by Cisco. Speed from the blade InfiniBand daughtercard to the switch is limited to IB 1X (2.5 Gbit). Externally the switch has one IB 4X and one IB 12X port. The IB 12X port can be split to three IB 4X ports, giving a total of four IB 4X ports and a total theoretical external bandwidth of 40 Gbit.

Two kinds of pass through module are available: copper pass through and fibre pass through. The copper pass through can be used only with Ethernet, while the Fibre pass through can be used for Ethernet, SAN or Myrinet.

Bridge modules are only compatible with BladeCenter H and BladeCenter HT. They function like Ethernet or SAN switches and bridge the traffic to InfiniBand. The advantage is that from the Operating System on the blade everything seems normal (regular Ethernet or SAN connectivity), but inside the BladeCenter everything gets routed over the InfiniBand.

High speed switch modules are compatible only with the BladeCenter H and BladeCenter HT. A blade that needs the function must have a high speed daughtercard installed. Different high speed daughtercards cannot be mixed in the same BladeCenter chassis.

A 10 Gigabit Ethernet switch module was available from BLADE Network Technologies. This allowed 10 Gbit/s connection to each blade, and to outside the BladeCenter.

The IBM Roadrunner supercomputer used a custom module called the TriBlade from 2008 through 2013. An expansion blade connects two QS22 modules with 8 GB RAM each via 4 PCIe x8 links to a LS21 module with 16 GB RAM, two links for each QS22. It also provides outside connectivity via an Infiniband 4x DDR adapter. This makes a total width of four slots for a single TriBlade. Three TriBlades fit into one BladeCenter H chassis.