Автоматты сағаттар және олардың жұмыс принципі

Timekeeping device that is driven by a spring that winds by motion of the wearer. An automatic watch, also known as a self winding watch or simply an automatic, is a mechanical watch where the natural motion of the wearer provides energy to wind the mainspring, making manual winding unnecessary if worn enough. It is distinguished from a manual watch in that a manual watch must have its mainspring wound by hand at regular intervals.

In a mechanical watch the watch's gears are turned by a spiral spring called a mainspring. In a manual watch, energy is stored in the mainspring by turning a knob, the crown, on the side of the watch. Then the energy from the mainspring powers the watch movement until it runs down, requiring the spring to be wound again. A self winding watch movement has a mechanism which winds the mainspring using the natural motions of the wearer's body. The watch contains an oscillating weight that turns on a pivot. The normal movements of the watch in the user's pocket (for a pocketwatch) or on the user's arm (for a wristwatch) cause the rotor to pivot on its staff, which is attached to a ratcheted winding mechanism. The motion of the watch is thereby translated into circular motion of the weight which, through a series of reverser and reducing gears, eventually winds the mainspring. There are many different designs for modern self winding mechanisms. Some designs allow winding of the watch to take place while the weight swings in only one direction while other, more advanced, mechanisms have two ratchets and wind the mainspring during both clockwise and anti clockwise weight motions. The fully wound mainspring in a typical watch can store enough energy reserve for roughly two days, allowing the watch to keep running through the night while stationary. In many cases automatic wristwatches can also be wound manually by turning the crown, so the watch can be kept running when not worn, and in case the wearer's wrist motions are not sufficient to keep it wound automatically.

Self winding mechanisms continue working even after the mainspring is fully wound up. If a simple mainspring was used, this would put excessive tension on the mainspring. This could break the mainspring, and even if it did not, it can cause a problem called "knocking" or "banking". The excessive drive force applied to the watch movement gear train can make the balance wheel rotate with excessive amplitude, causing the impulse pin to hit the back of the pallet fork horns. This will make the watch run fast, and could break the impulse pin. To prevent this, a slipping clutch device is used on the mainspring so it cannot be overwound.

The "slipping mainspring" device was patented by Adrien Philippe, one of the founders of Patek Philippe, on 16 June 1863, long before self winding wristwatches. In an ordinary watch mainspring barrel, the outer end of the spiral mainspring is attached to the inside of the barrel. In the slipping barrel, the mainspring is attached to a circular steel expansion spring, often called the 'bridle', which presses against the inside wall of the barrel, which has serrations or notches to hold it. As long as the mainspring is less than fully wound, the bridle holds the mainspring by friction to the barrel wall, allowing the mainspring to be wound. When the mainspring reaches full wind, its force is stronger than the bridle spring, and further winding pulls the bridle loose from the notches and it simply slides along the wall, preventing the mainspring from being wound further. The bridle must grip the barrel wall with just the right force to allow the mainspring to wind fully but not overwind. If it grips too loosely, the bridle will begin to slip before the mainspring is fully wound, a defect known as 'mainspring creep' which results in a shortened reserve power time. A further advantage of this device is that the mainspring cannot be broken by excessive manual winding. This feature is often described in watch company advertising as an "unbreakable mainspring".

Invented by John Harwood, a watch repairer from Bolton, England, who took out a UK patent with his financial backer, Harry Cutts, on 7 July 1923, and obtained a corresponding Swiss patent on 16 October 1923. The Harwood system used a pivoting weight which swung as the wearer moved, winding the mainspring. The ratchet mechanism wound the mainspring only when moving in one direction. The weight did not rotate a full 360°; spring bumpers limited its swing to about 180°, to encourage a back and forth motion. This early type of self winding mechanism is now referred to as a 'hammer' or 'bumper'. Like its 18th century counterparts, Harwood's watch also had a problem with jerking because "the brass weight hit too sharply against the banking pins as it pivoted". When fully wound, Harwood's watch would run for 12 hours autonomously. It did not have a conventional stem winder, so the hands were moved manually by rotating a bezel around the face of the watch. The watches were first produced with the help of Swiss watch manufacturer Fortis and went on sale in 1928. Thirty thousand were made before the Harwood Self Winding Watch Company collapsed in 1931 in the Great Depression. 'Bumper' watches were the first commercially successful automatic watches; they were made by several high grade watch manufacturers during the 1930s and 1940s.

The Rolex Watch Company improved Harwood's design in 1930 and used it as the basis for the Shants Company, in which the centrally mounted semi circular weight could rotate through a full 360° rather than the about 200° of the 'bumper' winder. Rolex's version also increased the amount of energy stored in the mainspring, allowing it to run autonomously for up to 35 hours. Information about 18th century rotor watches was not published until 1949. Although the Oyster Perpetual was probably an original invention, the company may have known of Coviot's 1893 patent that re invented the 18th century design.

With John Harwood's patent for self winding watches set to expire in the early 1930s, Glycine founder Eugène Meylan started developing his own self winding mechanism. Meylan’s design was unusual: a separate module that could be used with almost any 8.75 ligne (19.74 millimeter) watch movement. In October 1930, Glycine released their first automatic watches using this module, which became the world's first widely produced automatic watches. This allowed Glycine to survive the global depression in the 1930s that caused many Swiss watchmakers to close shop.

The next development for automatic watches came in 1948 from Eterna Watch. To wind a watch effectively, one of the chief requirements of a rotor is heft. Until this point, the best bearing used in any watch was a jewel bearing, which perfectly suits the small gears of a watch. A rotor, on the other hand, requires a different solution. In 1948, Eterna introduced the solution that is still in use today: ball bearings. Ball bearings provide robust support for a heavy object to rotate smoothly and reliably even under abnormal stress, such as if the watch were dropped. Eterna adopted geared bidirectional winding shortly afterwards.

By the 1960s, automatic winding had become widespread in quality mechanical watches. Because the rotor weight needed in an automatic watch takes up a lot of space in the case, increasing its thickness, some manufacturers of quality watches, such as Patek Philippe, continue to design manually wound watches, which can be as thin as 1.77 millimeters. However, in 2007 Carl F. Bucherer implemented a new approach without a rotor, a peripherally mounted power source, where a geared ring and a rotating unbalance mass segment made of tungsten encircles the entire mechanism, rotating on carbon rollers whenever the watch moves. A system of clutch wheels captures power. No rotor means thinner watches and an ultradense weight swinging around a greater radius means a better chance of achieving a greater power reserve with same amount of arm movement.