Ағылшыншамен салыстырыңыз: абзацты басыңыз — түпнұсқа терезеде ашылады. Абзац астындағы EN түймесі оны мәтін ішінде көрсетеді.
Кіріспе
Құбырдың ішкі диаметріне (ID) негізделген темір құбыр өлшемін (IPS немесе IPS) өлшеу жүйесі. Ол 19 ғасырдың басынан 20 ғасырдың ортасына дейін кеңінен қолданылған және кейбір өнеркәсіптер, соның ішінде ірі ПВХ құбыр өндірушілер, сондай-ақ кейбір мұралық сызбалар мен жабдықтар үшін әлі де қолданылуда. Темір құбыр өлшемі стандартты 19-ғасырдың басында пайда болды және Екінші дүниежүзілік соғыстан кейін ғана қолданылды. IPS жүйесі негізінен АҚШ пен Ұлыбританияда қолданылды. 1920 жылдары мыс түтіктің өлшемі (CTS) стандарты IPS стандартымен біріктірілді. IPS кезеңінде құбырлар жартылай құйылып, біріктірілді, ал құбырлардың өлшемдері ішкі диаметрлерге қатысты. IPS-тің ішкі диаметрлері қазіргі заманғы Ductile Iron Pipe Standard (DIPS) және Nominal Pipe Size (NPS) стандарттарымен шамамен бірдей болды, ал қабырғалардың кейбір қалыңдығы басқа белгімен сақталды. 1948 жылы DIPS күшіне енді, онда құбырдың қабырға қалыңдығын көбірек бақылауға болады. CTS диаметрі әрқашан түтіктің сыртқы диаметрі (OD) деп аталады, онда құбыр диаметрінің спецификациялары тек 12 дюйм немесе одан аз өлшемі үшін құбырдың ішкі диаметріне (ID) және STD қабырғасының қалыңдығына жуықталады. IPS нөмірі (OD-ге сілтеме) NPS нөмірімен бірдей, бірақ кестелер Стандартты қабырғаға (STD), Экстра Строг (XS) және Қос Экстра Строг (XXS) шектелген. STD NPS 1/8-ден NPS 10-ға дейінгі кестеге ұқсас және NPS 12-ден жоғары қабырға қалыңдығын 0,375 "көрсетеді. XS NPS 1/8-ден NPS 8-ге дейін SCH 80-ге ұқсас және NPS 8-ден жоғары қабырға қалыңдығын 0,500 "көрсетеді. XXS үшін әртүрлі анықтамалар бар, бірақ ол әдетте 160 кестеден қалың.
Iron Pipe Size (IPS or I. P. S.) pipe sizing system based on the inside diameter (ID) of pipe. It was widely used from the early 19th century to the mid 20th century and is still in use by some industries, including major PVC pipe manufacturers, as well as for some legacy drawings and equipment. The iron pipe size standard came into being early in the 19th century and remained in effect until after World War II. The IPS system was primarily used in the United States and the United Kingdom. In the 1920s, the Copper Tube Size (CTS) standard was combined with the IPS standard. During the IPS period, pipes were cast in halves and welded together, and pipe sizes referred to the inside diameters. The inside diameters under IPS were roughly the same as the more modern Ductile Iron Pipe Standard (DIPS) and Nominal Pipe Size (NPS) Standards, and some of the wall thicknesses were also retained with a different designator. In 1948, the DIPS came into effect, when greater control of a pipe's wall thickness was possible. CTS diameter always specifies the outside diameter (OD) of a tube, where pipe diameter specifications only approximate the pipe inside diameter (ID) for sizes of 12 inch or less, and STD wall thickness. The IPS number (reference to an OD) is the same as the NPS number, but the schedules were limited to Standard Wall (STD), Extra Strong, (XS) and Double Extra Strong (XXS). STD is identical to Schedule 40 for NPS 1/8 to NPS 10, inclusive, and indicates .375" wall thickness for NPS 12 and larger. XS is identical to SCH 80 for NPS 1/8 to NPS 8, inclusive, and indicates .500" wall thickness for NPS 8 and larger. Different definitions exist for XXS, but it is generally thicker than schedule 160.