Жерге қайтарылатын бір сымды қуат тарату жүйесі

Supply energy using single wire with earth as return
power distribution

Single wire earth return (SWER) or single wire ground return is a single wire transmission line which supplies single phase electric power from an electrical grid to remote areas at lowest cost. The earth (or sometimes a body of water) is used as the return path for the current, to avoid the need for a second wire (or neutral wire) to act as a return path. Single wire earth return is principally used for rural electrification, but also finds use for larger isolated loads such as water pumps. It is also used for high voltage direct current over submarine power cables. Electric single phase railway traction, such as light rail, uses a very similar system. It uses resistors to earth to reduce hazards from rail voltages, but the primary return currents are through the rails.

Lloyd Mandeno, OBE (1888–1973) fully developed SWER in New Zealand around 1925 for rural electrification. Although he termed it "Earth Working Single Wire Line", it was often called "Mandeno’s Clothesline". More than 200,000 kilometres (100,000 miles) have now been installed in Australia and New Zealand. It is considered safe, reliable and low cost, provided that safety features and earthing are correctly installed. The Australian standards are widely used and cited. It has been applied around the world, such as in the Canadian province of Saskatchewan; Brazil; Africa; and portions of the United States' Upper Midwest and Alaska (Bethel).

SWER is a viable choice for a distribution system when conventional return current wiring would cost more than SWER's isolation transformers and small power losses. Power engineers experienced with both SWER and conventional power lines rate SWER as equally safe, more reliable, less costly, but with slightly lower efficiency than conventional lines. SWER can cause fires when maintenance is poor, and bushfire is a risk. Power is supplied to the SWER line by an isolating transformer of up to 300 kVA. This transformer isolates the grid from ground or earth. The voltage changes due to the transition from line to line to line to earth, typically reducing a 22 kV grid to 12.7 kV SWER or a 33 kV grid to 19.1 kV SWER. The SWER line is a single conductor that may stretch for tens or even hundreds of kilometres, with a number of distribution transformers along its length. At each transformer, such as a customer's premises, current flows from the line, through the primary coil of a step down isolation transformer, to earth through an earth stake. From the earth stake, the current eventually finds its way back to the main step up transformer at the head of the line, completing the circuit. Experience in Alaska shows that SWER needs to be grounded below permafrost, which is high resistance. The secondary winding of the local transformer will supply the customer with either single ended single phase (N 0) or split phase (N 0 N) power in the region's standard appliance voltages, with the 0 volt line connected to a safety earth that does not normally carry an operating current. A large SWER line may feed as many as 80 distribution transformers. The transformers are usually rated at 5 kVA, 10 kVA, and 25 kVA. The load densities are usually below 0.5 kVA per kilometer (0.8 kVA per mile) of line. Any single customer's maximum demand will typically be less than 3.5 kVA, but larger loads up to the capacity of the distribution transformer can also be supplied. Some SWER systems in the USA are conventional distribution feeders that were built without a continuous neutral (some of which were obsolete transmission lines that were refitted for rural distribution service). The substation feeding such lines has a grounding rod on each pole within the substation; then on each branch from the line, the span between the pole next to and the pole carrying the transformer would have a grounded conductor (giving each transformer two grounding points for safety reasons).

Proper mechanical design of a SWER line can lower its lifetime cost and increase its safety. Since the line is high voltage, with small currents, the conductor used in historic SWER lines was Number 8 galvanized steel fence wire. More modern installations use specially designed AS1222.1 high carbon steel, aluminum clad wires. Aluminum clad wires corrode in coastal areas, but are otherwise more suitable. Because of the long spans and high mechanical tensions, vibration from wind can cause damage to the wires. Modern systems install spiral vibration dampers on the wires. In these jurisdictions, each SWER line must be approved by exception.

SWER's main advantage is its low cost. It is often used in sparsely populated areas where the cost of building an isolated distribution line cannot be justified. Capital costs are roughly 50% of an equivalent two wire single phase line. They can cost 30% of 3 wire three phase systems. Maintenance costs are roughly 50% of an equivalent three phase line. SWER also reduces the largest cost of a distribution network: the number of poles. Conventional 2 wire or 3 wire distribution lines have a higher power transfer capacity, but can require 7 poles per kilometre (12 poles per mile), with spans of 100 to 150 metres (110 to 160 yards). SWER's high line voltage and low current also permits the use of low cost galvanized steel wire (historically, No. 8 fence wire). The first step may be to replace the steel wire with more expensive copper clad or aluminum clad steel wire. It may be possible to increase the voltage. Some distant SWER lines now operate at voltages as high as 35 kV. Normally this requires changing the insulators and transformers, but no new poles are needed. If more capacity is needed, a second SWER line can be run on the same poles to provide two SWER lines 180 degrees out of phase. This requires more insulators and wire, but doubles the power without doubling the poles. Many standard SWER poles have several bolt holes to support this upgrade. This configuration causes most ground currents to cancel, reducing shock hazards and interference with communication lines. Two phase service is also possible with a two wire upgrade: Though less reliable, it is more efficient. As more power is needed, the lines can be upgraded to match the load, from single wire SWER to two wire, single phase and finally to three wire, three phase. This ensures a more efficient use of capital and makes the initial installation more affordable. Customer equipment installed before these upgrades will all be single phase, and can be reused after the upgrade. If small amounts of three phase power are needed, it can be economically synthesized from two phase power with on site equipment.

SWER lines tend to be long, with high impedance, so the voltage drop along the line is often a problem, causing poor regulation. Variations in demand cause variation in the delivered voltage. To combat this, some installations have automatic variable transformers at the customer site to keep the received voltage within legal specifications. After some years of experience, the inventor advocated a capacitor in series with the ground of the main isolation transformer to counteract the inductive reactance of the transformers, wire and earth return path. The plan was to improve the power factor, reduce losses and improve voltage performance due to reactive power flow. Alaska's state economic energy screening survey advocated further study of this option to use more of the state's underutilized power sources.

At present, certain developing nations have adopted SWER systems as their mains electricity systems, notably Laos, South Africa and Mozambique.

Many high voltage direct current systems (HVDC) using submarine power cables are single wire earth return systems. Bipolar systems with both positive and negative cables may also retain a seawater grounding electrode, used when one pole has failed. To avoid electrochemical corrosion, the ground electrodes of such systems are situated apart from the converter stations and not near the transmission cable. The electrodes can be situated in the sea or on land. Bare copper wires can be used for cathodes, and graphite rods buried in the ground, or titanium grids in the sea are used for anodes. To avoid electrochemical corrosion (and passivation of titanium surfaces) the current density at the surface of the electrodes must be small, and therefore large electrodes are required. Examples of HVDC systems with single wire earth return include the Baltic Cable and Kontek.