6,8 мм Remington SPC: промежуточный винтовочный патрон

Intermediate rifle cartridge

The 6.8mm Remington Special Purpose Cartridge (6.8 SPC, 6.8 SPC II or 6.8×43mm) is a rimless bottlenecked intermediate rifle cartridge that was developed by Remington Arms in collaboration with members of the U. S. Army Marksmanship Unit and United States Special Operations Command to possibly replace the 5.56 NATO cartridge in short barreled rifles (SBR) and carbines. Based on the .30 Remington cartridge, it is midway between the 5.56×45mm NATO and 7.62×51mm NATO in bore diameter. It uses the same diameter bullet (usually not the same mass) as the .270 Winchester hunting cartridge.

The 6.8mm SPC cartridge was designed to address the deficiencies of the terminal ballistics of the 5.56×45mm NATO cartridge currently in service with the armed forces of all NATO aligned countries. The cartridge was the result of the Enhanced Rifle Cartridge Program. The 6.8 SPC (6.8×43mm) was initially developed by Master Sergeant Steve Holland and Chris Murray, a United States Army Marksmanship Unit gunsmith, to offer superior downrange lethality over the 5.56 NATO/.223 Remington in an M16 pattern service rifle with minimal loss of magazine capacity and a negligible increase in recoil. The program started the design by using a .30 Remington case, which was modified in length to fit into magazines that would be accommodated by the magazine wells of the M16 family of rifles and carbines that are currently in service with the U. S. Armed Forces. In tests comparing various caliber bullets using a .30 Remington parent case, Holland and Murray determined that a 6.5 mm caliber projectile had the best accuracy and penetration, with historical data going back for decades of US Army exterior and terminal ballistic testing, but a 7 mm projectile had the best terminal performance. The combination of the cartridge case, powder load, and projectile easily outperformed the 7.62×39mm and 5.45×39mm Soviet cartridges, with the new cartridge's muzzle velocity proving to be about faster than the 7.62 x 39. The 6.8mm Remington SPC was designed to perform better in short barreled CQB rifles after diminished performance from the 5.56 NATO when the M16A4 was changed from the rifle configuration to the current M4 carbine. The 6.8 SPC delivers 44% more energy than the 5.56mm NATO (M4 configuration) at The 6.8mm SPC is not the ballistic equal of the 7.62×51mm NATO cartridge, but it has less recoil, has been said to be more controllable in rapid fire, and is lighter, allowing operators to carry more ammunition than would otherwise be possible with the larger caliber round. The 6.8 mm generates around of muzzle energy with a bullet. In comparison, the 5.56×45mm round (which the 6.8 is designed to replace) generates around with a bullet, giving the 6.8 mm a terminal ballistic advantage over the 5.56 mm of One of the enigmatic features of this cartridge is its being designed for a short barrel carbine length rifle than the standard rifle length is (usually ). The round only gains about for every 25 mm of barrel length past the standard barrel (all else being equal) up to barrel's length around with no gain or loss in accuracy. It also does well in rifles with less than barrels. In recent developments (the period 2008–2012) the performance of the 6.8 SPC has been increased by approximately by the work of ammunition manufacturer Silver State Armory LLC (SSA) and a few custom rifle builders using and designing the correct chamber and barrel specifications. The 6.8mm Remington SPC cartridge weighs, depending on the manufacturer and load, between Also, more recently, LWRC, Magpul and Alliant Techsystems (ATK) introduced a new AR 15 designed for the 6.8 SPC which allows for a proprietary 6.8 Magpul P mags and an overall cartridge length of The personal defense weapon (PDW) known as the "Six8" is SPC II w 1: twist and is able to use all current 6.8 SPC factory ammunition.

Nosler Accubond Silver State Armory (SSA) OTM Remington Premier Match Barnes TSX – SSA Nosler E Tip – SSA Nosler BSB – SSA Hornady V MAX Sierra Match King (SMK) OTM (FMJ) – SSA Barnes TSX – SSA "tactical" factory load Speer Gold Dot Federal(ATK) "tac/mil" load Barnes TTSX – Wilson Combat factory load SCHP – SSA "combat" factory load Hornady BTHP TAP – Hornady Law Enforcement "tactical" factory load BTHP OTM & Barnes TSX – Wilson "combat" factory load Berger VLD – SSA factory load. (Discontinued)

Cartridge Muzzle velocity drop velocity drop velocity 5.56×45mm M193 5.56×45mm OTM 6.8×43mm SPC SMK 6.8×43mm SPC V MAX 7.62×39mm 7.62×51mm SMK

Typical trajectory information from carbines with drop and velocity calculated at sea level with a zero.

By late 2004 the 6.8×43mm SPC was said to be performing well in the field against enemy combatants in special operations. However the cartridge was not used by conventional US military personnel. It was not adopted for widespread use due to resistance from officials. The 6.8 SPC was designed for better terminal effectiveness at the shorter ranges of urban combat experienced in Iraq. When fighting in Afghanistan began to intensify, engagements began taking place at greater distances, where the 6.8 SPC begins to falter. Experiments suggested that the comparatively short 6.8 mm bullets became ineffective at longer ranges. In 2007, both the U. S. SOCOM and the U. S. Marine Corps decided not to field weapons chambered in 6.8 mm due to logistical and cost issues. In April 2022, after enduring over 100 technical tests and firing more than 1.5 million rounds, the Army awarded a contract to Sig Sauer to produce the Next Generation Squad Weapon — or NGSW — XM7 Rifle, XM250 Automatic Rifle and a 6.8mm family of ammunition to replace the M4A1 Carbine, M249 Squad Automatic Weapon and 5.56mm family of ammunition within the close combat force. While there are many rumors of evaluations of the cartridge by several major federal and local law enforcement agencies, the US Drug Enforcement Administration has allowed individual agents to purchase the M6A2 D DEA – which uses the 6.8mm Remington SPC – as an authorized alternative to their duty weapon. In 2010 the Jordanian state owned arms manufacturer KADDB announced that they would be producing 6.8 mm rifles and carbines for the Jordanian Army. There is also a contract between LWRC, Magpul, Alliant Techsystems and the Saudi Royal Guard for around 36,000 Six8 PDWs and an undisclosed amount of ATK/Federal XD68GD (90gr Gold Dot "training" ammo) and proprietary Magpul 6.8 Pmags specifically for the LWRC Six8.

The first major manufacturer to offer a 6.8mm Remington SPC chambered version of the AR 15 was Barrett Firearms Company, offering the Barrett M468 and later the REC7. By 2007, most major manufacturers of AR 15 type rifles for the civilian gun market were offering rifles in this caliber. Dedicated AR upper receiver assemblies chambered for the round are produced by a number of smaller firms, including Daniel Defense. Ruger Firearms no longer produces a 6.8 mm for their Ruger SR 556 piston driven AR 15 variant. The Stag Arms hunter and tactical models utilize the newer chamber (SPC II) and specified twist rates to accommodate higher pressure loadings, as well as upper receivers in left handed configurations. Rock River Arms has an LAR 6.8 X Series rifle and uppers. Microtech Small Arms Research offers their version of the Steyr AUG in 6.8. Robinson Armament Co. offers the XCR L in 6.8, which can be easily converted between 6.8, 5.56, and 7.62×39. Bushmaster delivered a 6.8 SPC II conversion kit to the market as of October 2018. Ruger Firearms chambered their Mini 14 ranch rifle in this round for several years; however, it has been discontinued.