Введение
Потометр (от греческого ποτό = пьяный и μέτρο = мера), иногда называемый транспирометром, – это прибор, используемый для измерения скорости поглощения воды листовым побегом, которая почти равна количеству воды, потерянной при транспирации. Причинами поглощения воды являются фотосинтез и транспирация. Скорость транспирации можно оценить двумя способами: косвенно – путем измерения расстояния, на которое опускается уровень воды в градуированной трубке за определенный промежуток времени. Предполагается, что это связано с поглощением воды черенком, которое, в свою очередь, необходимо для восполнения равного объема воды, потерянной при транспирации. Непосредственно – путем измерения уменьшения массы потометра в течение определенного периода времени. В этом случае предполагается, что любая потеря массы обусловлена транспирацией. Существуют два основных типа потометров: пузырьковый (описан ниже) и весовой. Весовой потометр состоит из растения, корень которого погружен в стакан. Этот стакан затем помещается на цифровые весы; показания снимаются для определения количества воды, потерянной растением.
Indirectly by measuring the distance the water level drops in the graduated tube over a measured length of time. It is assumed that this is due to the cutting taking in water which in turn is necessary to replace an equal volume of water lost by transpiration. Directly by measuring the reduction in mass of the potometer over a period of time. Here it is assumed that any loss in mass is due to transpiration. There are two main types of potometers: the bubble potometer (as detailed below), and the mass potometer. The mass potometer consists of a plant with its root submerged in a beaker. This beaker is then placed on a digital balance; readings can be made to determine the amount of water lost by the plant. Design
Potometers come in a variety of designs, but all follow the same basic principle. A length of capillary tube. A bubble is introduced to the capillary; as water is taken up by the plant, the bubble moves. By marking regular gradations on the tube, it is possible to measure water uptake. A reservoir. Typically a funnel with a tap; turning the tap on the reservoir resets the bubble. Some designs use a syringe instead. A tube for holding the shoot'''. The shoot must be held in contact with the water; additionally, the surface of the water should not be exposed to the air. Otherwise, evaporation will interfere with measurements. A rubber bung greased with petroleum jelly suffices. Preparation
Cut a leafy'' shoot for a plant and plunge its base into water. This prevents the xylem from taking up any air. Wetting the leaves themselves will alter the rate of transpiration. Immerse the whole of the potometer into the sink. Move it about until all the air bubbles come out. Recut the shoot's stem underwater. Put it into the bung; grease the bung with plenty of petroleum jelly if it doesn't stay and then put the bung into the potometer. Make sure the tap is closed, then lift the whole assembly out of the water. Leave the end of the capillary tube out of the water until an air bubble forms, then put the end into a beaker of water.
Потометры имеют различные конструкции, но все они основаны на одном и том же принципе. Капиллярная трубка. В капилляр вводится пузырек, который перемещается по мере поглощения воды растением. На трубке наносятся регулярные деления для измерения поглощения воды. Резервуар. Обычно это воронка с краном; открытие крана в резервуаре возвращает пузырек в исходное положение. В некоторых конструкциях используется шприц. Трубка для фиксации побега. Побег должен находиться в контакте с водой; кроме того, поверхность воды не должна быть открыта для воздуха. В противном случае испарение будет мешать измерениям. Достаточно резиновой пробки, смазанной вазелином.
Indirectly by measuring the distance the water level drops in the graduated tube over a measured length of time. It is assumed that this is due to the cutting taking in water which in turn is necessary to replace an equal volume of water lost by transpiration. Directly by measuring the reduction in mass of the potometer over a period of time. Here it is assumed that any loss in mass is due to transpiration. There are two main types of potometers: the bubble potometer (as detailed below), and the mass potometer. The mass potometer consists of a plant with its root submerged in a beaker. This beaker is then placed on a digital balance; readings can be made to determine the amount of water lost by the plant. Design
Potometers come in a variety of designs, but all follow the same basic principle. A length of capillary tube. A bubble is introduced to the capillary; as water is taken up by the plant, the bubble moves. By marking regular gradations on the tube, it is possible to measure water uptake. A reservoir. Typically a funnel with a tap; turning the tap on the reservoir resets the bubble. Some designs use a syringe instead. A tube for holding the shoot'''. The shoot must be held in contact with the water; additionally, the surface of the water should not be exposed to the air. Otherwise, evaporation will interfere with measurements. A rubber bung greased with petroleum jelly suffices. Preparation
Cut a leafy'' shoot for a plant and plunge its base into water. This prevents the xylem from taking up any air. Wetting the leaves themselves will alter the rate of transpiration. Immerse the whole of the potometer into the sink. Move it about until all the air bubbles come out. Recut the shoot's stem underwater. Put it into the bung; grease the bung with plenty of petroleum jelly if it doesn't stay and then put the bung into the potometer. Make sure the tap is closed, then lift the whole assembly out of the water. Leave the end of the capillary tube out of the water until an air bubble forms, then put the end into a beaker of water.
Подготовка. Срежьте лиственный побег растения и погрузите его основание в воду. Это предотвращает попадание воздуха в ксилему. Увлажнение листьев изменит скорость транспирации. Погрузите весь потометр в раковину. Перемещайте его, пока не выйдут все пузырьки воздуха. Под водой снова срежьте стебель побега. Вставьте его в пробку; обильно смажьте пробку вазелином, если она не держится, а затем вставьте пробку в потометр. Убедитесь, что кран закрыт, затем выньте всю сборку из воды. Оставьте конец капиллярной трубки вне воды до образования воздушного пузырька, затем поместите конец в стакан с водой.
Indirectly by measuring the distance the water level drops in the graduated tube over a measured length of time. It is assumed that this is due to the cutting taking in water which in turn is necessary to replace an equal volume of water lost by transpiration. Directly by measuring the reduction in mass of the potometer over a period of time. Here it is assumed that any loss in mass is due to transpiration. There are two main types of potometers: the bubble potometer (as detailed below), and the mass potometer. The mass potometer consists of a plant with its root submerged in a beaker. This beaker is then placed on a digital balance; readings can be made to determine the amount of water lost by the plant. Design
Potometers come in a variety of designs, but all follow the same basic principle. A length of capillary tube. A bubble is introduced to the capillary; as water is taken up by the plant, the bubble moves. By marking regular gradations on the tube, it is possible to measure water uptake. A reservoir. Typically a funnel with a tap; turning the tap on the reservoir resets the bubble. Some designs use a syringe instead. A tube for holding the shoot'''. The shoot must be held in contact with the water; additionally, the surface of the water should not be exposed to the air. Otherwise, evaporation will interfere with measurements. A rubber bung greased with petroleum jelly suffices. Preparation
Cut a leafy'' shoot for a plant and plunge its base into water. This prevents the xylem from taking up any air. Wetting the leaves themselves will alter the rate of transpiration. Immerse the whole of the potometer into the sink. Move it about until all the air bubbles come out. Recut the shoot's stem underwater. Put it into the bung; grease the bung with plenty of petroleum jelly if it doesn't stay and then put the bung into the potometer. Make sure the tap is closed, then lift the whole assembly out of the water. Leave the end of the capillary tube out of the water until an air bubble forms, then put the end into a beaker of water.
Использование
измерение скорости поглощения воды лиственным побегом, почти равной скорости потери воды при транспирации.
Меры предосторожности
Когда черенoк срезают с растения, его следует немедленно поместить под воду (только срезанную часть). Затем под водой срезают небольшой участок. Это предотвращает попадание воздуха в сосуды ксилемы. Условия работы потeнциального устройства, за исключением тестируемого изменения, не должны меняться во время эксперимента, так как внешние условия (например, температура) определяют поглощение воды. Все должно быть абсолютно герметичным, чтобы исключить утечки.
Ограничения
Потометр измеряет скорость поглощения воды, которая отличается от транспирации как таковой. Это происходит потому, что не вся вода, поглощенная растением, используется для транспирации (поглощенная вода может использоваться для фотосинтеза или клетками для поддержания тургора). Для непосредственного измерения скорости транспирации, а не скорости поглощения воды, следует использовать научный прибор, который количественно определяет перенос воды в листьях. Однако, как правило, количество воды, удерживаемой растением, настолько мало, что им можно пренебречь.