Модифицированная частотная модуляция (MFM) в ранних магнитных накопителях.

Line code used in early magnetic data storage

Modified frequency modulation (MFM) is a run length limited (RLL) line code used to encode data on most floppy disks and some hard disk drives. It was first introduced on hard disks in 1970 with the IBM 3330 and then in floppy disk drives beginning with the IBM 53FD in 1976. MFM is a modification to the original frequency modulation encoding (FM) code specifically for use with magnetic storage. MFM allowed devices to double the speed data was written to the media as the code guaranteed only one polarity change per encoded data bit. For this reason, MFM disks are typically known as "double density" while the earlier FM became known as "single density". MFM is used with a data rate of 250–500 kbit/s (500–1000 kbit/s encoded) on industry standard 5 1/4 inch and 3 1/2 inch ordinary and high density floppy diskettes. MFM was also used in early hard disk designs, before the advent of more efficient types of RLL codes. Outside of niche applications, MFM encoding is obsolete in magnetic recording.

Magnetic storage devices, like hard drives and magnetic tape, store data not as absolute values, but in the changes in polarity. This is because a changing magnetic field will induce an electrical current in a nearby wire, and vice versa. By sending a series of changing currents to the read/write head while the media moves past it, the result will be a pattern of magnetic polarities on the media that change where the data was a "1". The exact nature of the media determines how many of these changes can occur within a given surface area, and when this is combined with the nominal speed of movement, it produces the maximum data rate for that system. Disk drives are subject to a variety of mechanical and materials effects that cause the original pattern of data to "jitter" in time. If a long string of "0" are sent to disk, there is nothing to indicate which bit a following "1" might belong to due to the effects of jitter it may become misplaced in time. Re aligning the signals on the disk with individual data bits requires some sort of timing encoded to the disk along with the data. A diverse range of suitable encodings, known generally as line codes, have been developed for this purpose. Their suitability depends on the media or transmission mechanism being used.

Frequency modulation encoding (FM) was the first widely used system to perform this operation. The drive controller includes an accurate clock running at half the selected data rate of the disk media. When data is written to the disk, the clock signal is interleaved with the data. On reading, the clock signals are used as short term triggers to time the presence or lack of a following signal that represents the data bits. The upside to the FM approach is that it is extremely easy to implement the writing circuity and the clock recovery on reading is also relatively simple. The downside is that it uses up half of the disk surface for the clock signal, thus halving the total amount of data the disk can store. This led to new forms of encoding that were more efficient.

Because the MFM system requires more accurate timing of the clock signal, it was not possible economically to build the required analog and digital components on a single integrated circuit using late 1970s technology. Instead, MFM drivers required the drive vendor to design their own clock recovery circuitry, a system known as the data separator. Data separator design was an art form of its own. Among the most widely used controllers of the era was the Western Digital FD1771 series. The original FD1771 supported FM only, but it was quickly paired with the FD1781 and FD1791 which performed MFM based on an externally provided clock signal. Implementing MFM support with these drivers required an external data separator. Rapid improvement in IC manufacturing in the late 1970s and early 1980s led to the first low cost all in one MFM drivers in the early 1980s. The WD2791 was the first to directly support MFM using an internal analog phase locked loop, but it required a number of simple external components to implement a complete system. The WD1770 was the first to implement a complete MFM solution in a single chip.

MMFM, (Modified Modified Frequency Modulation), also abbreviated M²FM, or M2FM, is similar to MFM, but suppresses additional clock bits, producing a longer maximum run length (a (1,4) RLL code). In particular, a clock pulse is only inserted between a pair of adjacent 0 bits if the first bit of the pair did not have a clock pulse inserted before it.