Форд Эссекс V6 қозғалтқышы: Тарихы мен ерекшеліктері

The Ford Essex V6 engine is a 60° V6 engine built between 1966 and 1988 by the Ford Motor Company in the United Kingdom and until 2000 in South Africa although mostly in the Ford engine plant of Dagenham, Essex, which gave the engine its name. It is closely related to the Ford Essex V4 engine produced in displacements of 1.7 L and 2.0 L. Both engines share many parts since the Essex V6 was directly derived from the Essex V4; the 2.0 L Essex V4 and the 3.0 L Essex V6 in fact have exactly the same bore and stroke and share various components. In the same era, the Ford Cologne V6 engine was produced.

The Essex V4 and V6 were mainly designed to replace the outdated and ageing inline four and six cylinder Ford Zephyr engines. It was produced in four capacities: , , , , with the 3.0 litre version being the most common and widely used. These engines were fitted to a wide range of vehicles, from Ford Transit vans to sedans, coupés like the Ford Capri and sports cars like TVRs and Marcos. The earlier versions of engine were rated at and of torque, around October 1971 the engine was revised by modifying the camshaft and cylinder heads which improved the power and torque to produce SAE or DIN at 5000 rpm and SAE or DIN of torque at 3000 rpm. At the same time, the oil dipstick was moved from the front of the engine to the side, the inlet manifold was improved from earlier models, and the compression ratio was raised slightly from 8.9:1 to 9.0:1 due to a change of the piston design. The shape of the inlet ports was also changed from an O port design to a D port design which improved the flow characteristics of the heads, the old 40 DFAV Weber carburetor that was prone to over fueling and resulting bore wash was replaced by the 38 DGAS Weber carburetor, the air filter housing was also changed and later around 1976 a hot air intake was added consisting of a metal pipe running from the top of a plate welded on the exhaust manifold or header to an opening in the air intake to prevent the carburetor from icing and making the engine warm up more quickly. The carburetor was also modified again, a return style fuel system was adopted and a vacuum operated choke in the air filter housing were also added. This, and a positive crankcase ventilation (PCV) system were also early forms of emissions control. The camshaft gear was also made slightly stronger by using steel with nylon teeth instead of being completely made from nylon as on previous ones. Aftermarket steel, aluminium, and alloy gears have been produced as replacements to prevent the gear from stripping its teeth: this is commonly due to overheating causing the nylon to weaken. This is one of the two major weak points of the Essex V engines, the other being the hexagonal oil pump spindle / shaft which can round off, or even break. The 2.5 L engine was rated at SAE gross or DIN and peak torque was rated at SAE gross or DIN. The V6 engine as used in the Ford Capri RS 3100 was essentially a 3.0 L engine bored out by or 60 thousands of an inch from to It was capable of at 5000 rpm and of torque at 3000 rpm. It featured blue rocker covers in order to distinguish the engine from the usual 3.0 L engine and it also featured hand polished and ported inlet and exhaust ports. Only 250 RS 3100s were produced for homologation purposes, making original 3.1 litre engines very rare, although modified engines bored +0.60 are common, one of the first 50 engines which was in a RS 3100 that was free for car magazines to review and test in fact had instead of the of the rest of road going RS 3100s, this was achieved with a higher lift camshaft. These figures vary somewhat depending on the source. The Essex V6 also formed the base for the 3.4 L Cosworth GAA born in May 1972 and designed by Mike Hall, also responsible for designing Cosworth's famous DFV Engine. Ford RS dealerships also offered a number of performance modifications for the Essex V6, called the "GP1" (Group 1) and "Series X", the GP1 package offered a 40 DFI5 Weber carburetor, a camshaft kit, larger, , inlet and exhaust valves, double valve springs, specially selected connecting rods and forged high compression pistons giving a power output of around The Series X modifications offered the same larger inlet and exhaust valves as the GP1, but also offered a new inlet manifold designed for three twin choke 42 DCNF Weber carburetors fed by an electric fuel pump which boosted power up to and , however the standard camshaft was retained. Earlier versions of the 3.0 litre engine (pre October 1971) were fueled by a twin choke 40 DFAV Weber carburetor, which had some inherent faults in its design which caused it to run too rich and cause bore wash. It was subsequently replaced by a more modern twin choke 38 DGAS Weber carburetor which effectively solved the problems of the earlier carburetors, and was used for the 3 litre V6 until the end of its production. the Essex V6 also has a very heavy yet sturdy four main bearing crossplane crankshaft with large main journals, and a heavy flywheel in order to smooth out the power delivery, sometimes Essex V6 engines are referred to as an "Essex lump" referring to the weight of these engines. In spite of its heaviness, the Essex V6 was used as the main workhorse and a high performance option for medium to full sized cars like the Capri the Granada and Transit. Ford supplied Essex V6 powered Transit vans to the police and ambulance services in the UK from the late 1960s until 1989, when it was replaced by more modern engines such as the fuel injected 2.8 and 2.9 L Ford Cologne V6 engine although the Essex V6 was even used until April 2000 in South Africa. TVR contracted the company Broadspeed to develop a turbocharging system for their TVR 3000S turbo. In lieu of fuel injection, the carburettor was run inside a pressurized box atop the engine, and the turbocharger itself was mounted low and forward in the engine compartment, requiring the exhaust manifolds to exit forward. The compression ratio was lowered from 9.0:1 to 8.0:1 to reduce the engine's internal stresses. Turbocharging substantially increased horsepower, from and torque from
Broadspeed also designed a turbocharging system for the Mk1 Ford Capri 3.0, available since early 1970 these Capris were known as "Broadspeed Bullet Capris". The engine was heavily modified and included modified cylinder heads, a high lift camshaft, a re jetted carburetor, a completely blueprinted rotating assembly, lowered 8.2:1 compression ratio, a modified inlet manifold and exhaust system using a single turbocharger. Their power was substantially increased (by 63%) from Similar to the TVR 3000S' turbocharging system, it used a "blow through carburettor" system in which the standard but re jetted 38 DGAS Weber carburetor was run inside a pressurised airbox. Performance figures further increased with the uprated post October 1971 versions of the engine. The 2.5 L and 3.0 L engines share the same block, connecting rods and bore, differing only in crank throw and pistons, 3.0 L pistons have a length of and 2.5 L pistons have a length of /
.

In 1977, Californian company Olson Engineering, Inc. was contracted by TVR to design modifications to the Essex V6 such that it could be emissions certified for use in the United States. This allowed TVR to sell its Essex engined M Series cars in that market for the 1978 and 1979 model years. An owner's handbook supplement for US Federal models indicates that the emissions control system used a catalytic converter, exhaust gas recirculation, and secondary air injection. A shipment of approximately twenty 3000Ss arrived in September 1979, and were marked by the import company as being emissions compliant without the Olson Engineering emissions kit actually having been fitted. Dealers were made aware of this fact, but were each apparently coerced into buying at least two of the non compliant cars with the threat of withholding spare parts for other TVR models. One dealer explained the situation to a customer who happened to work for the US government in an emissions regulation capacity, and he reported the violation to the authorities. The cars were then impounded. During the long period of time during which Martin Lilley attempted to communicate with US customs officials to resolve the situation, the cars were neglected and stored outside, where they deteriorated and were vandalized. The cars were eventually re exported, repaired, and sold in Germany, but the short term financial impact of the unsalable cars (worth over £100,000 in total) was damaging to the development of the M Series replacement, the Tasmin.

In South Africa, the engine continued in production from 1982 up to April 2000 for use in the Sapphire Saloon and Sierra vehicles, and Courier pick ups. Late in its production life it was fitted with Lucas controlled electronic fuel injection designed by SAMCOR (South African Motor Corporation – now Ford SA) in co operation with the University of Pretoria's engineering department. This conversion resulted in a power increase from to of the standard 3.0 version, and for the fuel injection version, plus a useful boost to fuel economy. Only about 1,600 of the EFI variants were produced during 1992 and 1993. In October 1997, the 3.0L was enlarged to 3.4L by boring the cylinders and a new crankshaft with a stroke of giving a displacement of , this was done for the engine to be better suited to 4x4 vehicles where torque is needed. The 3.4 version produced and All 3.4 variants used the 38DGAS Weber carburetor with venturis. Production tooling at the factory was scrapped and sold in 2000, to make way for the production of a new four cylinder OHC engine, the remaining old stock of 3.4 L Engines started to be sold as assembled crate engines, these engines had some differences from the 2.5 3.0 and 3.1 L Dagenham built engines such as: Ford Cologne 2.8 / 2.9 V6 forged connecting rods, German made pistons with moly coating, smaller crank journals which reduced bearing speed, more aggressive camshaft timing and higher lift, larger inlet valves, shaft mounted rockers from Ford's Cologne 2.8 / 2.9 V6 engine, unique cylinder head castings with extra oil galleries, solid pushrods with no oiling holes, unique exhaust manifold bolt pattern due to the head castings also being unique to the 3.4 litre engine and an improved inlet manifold with larger runners and an improved plenum chamber. From 1966 to 1998, the 3.0L was also used in industrial applications such as generator plants, airport vehicles, milk vans, jet boats (Hamilton jet) and even river barges.

The Essex V6 was fitted to a wide variety of cars, both from Ford and from smaller specialist manufacturers that used Ford engines. Among these were the following: