Алғашқы Macintosh компьютерінің құрылымы мен технологиясы

The original Macintosh was a relatively simple machine, now of interest for its simplicity and for the fact that it was the first computer produced by Apple under the name Macintosh. The Macintosh used standard off the shelf components to the greatest extent possible, achieving a moderate price point by mixing complex LSI chips, readily customizable programmable array logic, and off the shelf components.

The Macintosh used the Motorola 68000. The 68000's bus was wired directly to the other programmable components of the computer: the IWM floppy controller, the Zilog 8530 SCC, and the MOS Technology 6522. The bus also connected the 68000 to the 128 or 512 KiB of main memory (DRAM), which was shared between the processor and the multimedia circuits in a direct memory access (DMA) arrangement. Either the processor or the video/sound engine could access the memory, but not both, resulting in up to a 10% loss in performance; the DMA circuit also performed necessary maintenance on the RAM which would otherwise add overhead, a trick previously used in the Apple II. Precise timing information was relayed to the 68000 by interrupts. The 68000 provides three interrupt inputs, which in the Macintosh 128K/512K were connected to the 6522, the 8530, and a human input designed for programmers, in order of increasing priority. Thus typing on the keyboard (attached to the 6522) did not reduce serial data (8530) performance, yet the program controlling the serial bus could be debugged by the programmer. To further reduce the cost of manufacture, as compared with its predecessor the Lisa, Apple did not include an MMU. As a result, the Macintosh did not support protected memory. Protected memory was only added to Macintosh computers with the release of the Mac OS X operating system. According to Andy Hertzfeld the Macintosh used for the introduction demo on January 24, 1984, was a prototype with 512k RAM, even though the first model offered for sale implemented just 128k of non expandable memory. This prototype was used to provide adequate RAM to run the memory intensive demo, which showcased speech synthesis software intended to impress the crowd.

The above components implemented the Macintosh GUI and networking as described below.

The centerpiece of the new interface was mouse driven control. The mouse contained only electromechanical components: a button, and two optical encoders. The button was connected to the 6522. The encoders' four outputs were connected two to the 8530 and two to the 6522. The optical encoders detected movement by quadrature. Each encoder had a wheel with radial stripes which would interrupt the light passing between an LED and a light detecting photodiode, producing electrical pulses with mouse movement. Both the X and the Y encoders were turned by frictional contact with the mouse ball. Two pairs of emitters and detectors were used on each encoder. A first set of pulses is enough to detect the rate of rotation without indicating the direction of rotation, and a second set of synchronized but 90° out of phase pulses provides the direction of rotation. Therefore, two emitter detector pairs were used for X and Y each. The motion detection signals connected to the 8530 chip using two non essential pins used for obsolete modems. Originally these signaled modem connection or disconnection. When the mouse moved by a certain amount, the modem connect/disconnect signal would change state and the 8530 would interrupt the processor. The operating system would then read the direction signals from the 6522 to differentiate left from right, and up from down, and move the mouse cursor.

The mouse cursor was drawn on the screen by software, as were all other on screen objects. To support real time animation the screen timing PAL circuit would send a pulse to the 6522 once per vertical retrace. This was the basis for an operating system service called the VBL (vertical blanking) Manager. When the screen was to be redrawn, the cursor would be moved and games had an opportunity to update the display. It could sometimes be difficult to avoid a race condition between a game and the raster display. Flicker could result from the processor writing to the image while it was being sent to the CRT. Therefore, the Macintosh provided a choice of two images in memory, so one could be read while the other was written. The "page" was selected by a general purpose I/O output connected from the 6522 to the video DMA. As two images added up to 42.75 KiB of precious RAM, however, this feature was unpopular. The DMA graphics controller operated independently and autonomously. One bit pixels were fetched sixteen at a time over a 16 bit data bus and output at just less 16 MHz, necessitating almost one million fetches per second. Each fetch took one memory access cycle out of every two available during active parts of the display, implying a memory bandwidth for the CPU of about 2.56MB per second.

The 6522 provided a general purpose serial bus. The keyboard contained an Intel 8021 microprocessor which transmitted user input to the 6522 over standard phone patch cable. A new keystroke resulted in a processor interrupt.

The sampled sound engine piggybacked on the video circuit. As the raster scan returned from the right side of the screen to the left, one byte of data was placed into a PWM generator instead of the screen. This provided 8 bit sampled monaural sound sampled at the 22.25 kHz horizontal blanking rate. General purpose 6522 outputs could mute the sampled sound, or set its volume to one of 8 levels of attenuation. A square wave generator was included on the 6522. One of its two timer circuits could be set to toggle the mute output periodically. This could produce frequencies higher than 11 kHz. This system was not compatible with the Lisa / Mac XL hardware, which in other respects could run Mac software with commonly available software/firmware modifications. Running programs on Lisas which made use of the Mac sound features would cause severe video problems and system crashes.

The Zilog 8530 SCC was clocked at around 3.7 MHz. At this speed each serial channel was half as fast as the main memory. The RS 422 protocol was implemented except for the connection established line, which was used to support the mouse. Apple later changed to an 8 pin connector which dropped it entirely.

The Macintosh's persistent storage medium was Sony's floppy diskette drive. This drive replaced the Apple ]['s Shugart drive and the 871K FileWare/"Twiggy" floppy drive used in the original Lisa as the storage medium chosen for the original Macintosh. The single sided 3.5 inch floppy stored 400 KB by spinning the disk slower when the outer edge was used. A separate microcontroller, the IWM (Integrated Woz Machine), was dedicated to disk control. The floppy operated by polled I/O so access was not seamless: loading and saving files were operations that stopped the entire machine. Twenty bytes of memory were included in the real time clock counter chip. This data was retained using a 4.5 Volt alkaline battery and was used to store user preferences.

The Macintosh featured a real time clock counting seconds, and a countdown timer with near microsecond resolution. The former was connected to the 6522 by a serial bus on three general purpose I/O lines. It functioned much as a quartz watch when the machine was powered off. The latter was built into the 6522 itself. Either could generate interrupts.