Счетчик осей в железнодорожной автоматике

An axle counter is a system used in railway signalling to detect the clear or occupied status of a section of track between two points. The system generally consists of a wheel sensor (one for each end of the section) and an evaluation unit for counting the axles of the train both into and out of the section. They are often used to replace a track circuit.

An axle counter consists of a sensor, which detects the individual axles of a train by mechanical, electrical or even fibre optic method, and an evaluator which counts the axles passing into and out of a rail section. The evaluator may also convert the analogue signal of the axle sensor into a digital signal. However, in some cases there is a separate unit which performs this task. The system is set up by having an axle counter sensor installed at each end of a section. As each train axle passes the axle counter sensor at the start of the section, a counter increments. An axle counter sensor comprises two independent sensors (so the device can detect the direction and speed of a train by the order and time in which the sensors are passed). As the train passes a similar axle counter sensor at the end of the section, the system compares count at the end of the section with that recorded at the beginning. If the two counts are the same, the section is presumed to be clear. This process is carried out by safety critical centrally located computers, called "evaluators", with the axle counter sensors located at the required sites in the field. The axle counter sensors are either connected to the evaluator via dedicated copper cable or via a telecommunications transmission system. That allows the axle counter sensors to be located a significant distance from the evaluator, and is useful when using centralised interlocking equipment, but less so when signalling equipment is situated beside the line in equipment cabinets.

The most common use for axle counters is in railway signalling for track vacancy detection. It is a form of block signalling, which does not permit two trains to be within the same section of track (block) at the same time. Block signalling decreases the chance of collision, because dividing the track into blocks ensures there is always enough space between trains to allow one to stop before it hits one in front.

Axle counters are also used to switch on and switch off warning equipment at level crossings, closing the crossing to pedestrian and motor vehicles when the presence of a train is detected, and allowing them to open when the train has passed over the crossing.

Axle counters are used in rail yards to detect train cars as they are sorted. Axle counters are placed on the track before each switch and on each track that exits the switch. Rail yard management software uses occupancy data from the axle counters to lock switches and prevent cars from being routed to tracks that are occupied by other cars.

Unlike traditional track circuits, axle counters do not require insulated rail joints to be installed. This avoids breaking the continuity of long sections of welded rail to allow insulated joints to be inserted.

Axle counters are particularly useful on electrified railways as they eliminate the need for traction bonding and impedance bonds. Axle counters require no bonding and less cabling in comparison to track circuits, and are therefore generally less expensive to install and maintain.

Axle counters eliminate most railjoints (IRJ) which are a weak point on the track.

Axle counters do not suffer problems with railhead contamination due to rust, grease or compacted leaf residue. Sometimes a train puts down anti slip sand to aid deceleration while braking, but the sand contaminates the rail and the track circuit stops working. Axle counters are immune to those problems because they do not rely on the contact of wheel with the rail head to provide an electrical circuit.

Axle counters are used in wet tunnels (such as the Severn Tunnel), where ordinary track circuits are unreliable. Axle counters are also useful on steel structures (such as the Forth Bridge), which may prevent the normal operation of track circuits if insulating the rails from the structure proves impracticable. Axle counters are also useful on long sections where the need for several intermediate track circuits may be saved. An axle counter can go up to around from the evaluation unit when connected directly. However, with the addition of an Ethernet network, the distance is limited by the transmission system.

For various reasons, such as a power failure, axle counters may 'forget' how many axles are in a section. A manual override is therefore necessary to reset the system. This manual override introduces the human element which may be unreliable. An accident which occurred in the Severn Tunnel is thought to have been due to the improper restoration of an axle counter. That was not proven during the subsequent inquiry, however. In older installations, the evaluators may use 8 bit logic, causing numeric overflow when a train with 256 or more axles passes the axle counter. As a result, that train would not be detected. That imposes a length limit of 255 axles on each train. More modern systems are not restricted by train wheel numbers.

Where there are interlocked turnouts, an axle counter unit needs to be provided for each leg of that turnout. On lines with non interlocked/hand operated switches, detection of the switch points would have to be monitored separately, whereas on track circuited lines misaligned points can be set to automatically break the track circuit.

A track circuit system does facilitate the detection of many, but not all, kinds of broken rails, though only to a limited extent in AC traction areas, and not in the common rail in DC traction areas. By contrast, axle counters cannot detect broken rails at all. Ordinary track circuits do have a blind spot of about a metre in length from the wiring connections to the insulated rail joint (IRJ).

Axle counters have problems maintaining correct counts when train wheels stop directly on the counter mechanism. That is known as 'wheel rock', and can prove problematic at stations or other areas where cars are shunted, joined and divided. Also, where main lines have switches to siding, spur or loop tracks, extra counters will need to be deployed to detect trains entering or exiting the line, whereas the same infrastructure using track circuits needs no special attention. In Auckland, New Zealand, axle counters have been used on all lines where track circuits are required, except for special places where Hi Rail maintenance vehicles either on or off track. All road crossing tracks at public level crossings are deemed to be Hi Rail access points and a short single rail DC track circuit is used. There are also several single rail DC track circuits at places not at level crossings where Hi Rail vehicles can access the track.

Magnetic brakes are used on high speed \ higher speed trains with a maximum speed greater than These are physically large pieces of metal mounted on the bogie of the vehicle, only a few centimetres above the track. They can sometimes be mistakenly detected by axle counters as another axle. This can happen at only one end a track block, because of magnetic field curvature, defects of track geometry,or other issues, leading the signalling system to become confused, and also requiring reset of the detection memory. Modern axle counters are 'eddy current' brake proof and the magnetic effect of the braking system as described above is overcome, with count information remaining stable even when a vehicle fitted with magnetic brakes is braking whilst traversing the detection point.

One method of mounting an axle counter sensor is to drill through the rail, however this is often seen as time consuming, as well as having the disadvantage of weakening the structure of the rail. However. it does eliminate the need for levelling, which can help reduce maintenance costs. Another installation method is to mount the Axle Counter Sensor onto a mount which clamps to both sides of the rail from underneath. That is quicker and easier to mount in the right conditions, but can mean more frequent checks to ensure correct positioning is maintained.