Зәйтүн майын алу процесі

Process of extracting oil from olives

Olive oil extraction is the process of extracting the olive oil present in olive drupes. Olive oil is produced in the mesocarp cells, and stored in a particular type of vacuole called a lipo vacuole, i. e., every cell contains a tiny olive oil droplet. Olive oil extraction is the process of separating the oil from the other fruit contents (vegetative extract liquid and solid material). It is possible to attain this separation by physical means alone, i. e., oil and water do not mix, so they are relatively easy to separate. This contrasts with other oils that are extracted with chemical solvents, generally hexane. The first operation when extracting olive oil is washing the olives, to reduce the presence of contaminants, especially soil which can create a particular flavor effect called "soil taste".

People have used olive presses since Greeks first began pressing olives over 5,000 years ago. Roman olive presses survive to the present time, with a notable collection present at Volubilis in Morocco. An olive press works by applying pressure to olive paste to separate the liquid oil and vegetation water from the solid material. The oil and vegetation water are then separated by standard decantation. Olive presses were traditionally built within walled structures. Traditional olive presses consisted of a large, cylindrical millstone mounted by an upper milling stone used to grind the olives and their pits into a pulp. Formerly, the upper milling stone was turned by a beast of burden pulling a wooden beam attached to the stone. After which, the pulp was collected and kneaded. It was then placed within frails (being no more than flexible, woven baskets made of thick fibrous material, usually of rushes, palm fronds, hemp or willow splints), stacked one on top of the other, to which was applied a stone weight to release the oil from the pulp. The extracted liquid which is obtained consists of oil and vegetable water (amurca) mixed together, The finest oil was produced from fully developed and ripe olives harvested solely from the apex of the tree, and lightly pressed, "for what flows from light pressure is very sweet and very thin." The remaining olives are pressed with a heavier weight, Others are left for extended periods in pits in the ground to induce sweating and decay before they are ground. According to the Geoponica, salt and a little nitre are added when oil is stored.

The modern method of olive oil extraction uses an industrial decanter to separate all the phases by centrifugation. In this method the olives are crushed to a fine paste. This can be done by a hammer crusher, disc crusher, depitting machine or knife crusher. This paste is then malaxed for 30 to 60 minutes in order to allow the small olive droplets to agglomerate. The aromas are created in these two steps through the action of fruit enzymes. Afterwards the paste is pumped into an industrial decanter where the phases will be separated. Water is added to facilitate the extraction process with the paste. The decanter is a large capacity horizontal centrifuge rotating approximately 3,000 rpm, the high centrifugal force created allows the phases to be readily separated according to their different densities (solids > vegetation water > oil). Inside the decanter's rotating conical drum there is a coil that rotates more slowly, pushing the solid materials out of the system. The separated oil and vegetation water are then rerun through a vertical centrifuge, working around 6,000 rpm that will separate the small quantity of vegetation water still contained in oil and vice versa.

With the three phases oil decanter, a portion of the oil polyphenols is washed out due to the higher quantity of added water (when compared to the traditional method), producing a larger quantity of vegetation water that needs to be processed. The two phases oil decanter was created as an attempt to solve these problems. Sacrificing part of its extraction capability, it uses less added water thus reducing the phenol washing. The olive paste is separated into two phases: oil and wet pomace. This type of decanter, instead of having three exits (oil, water, and solids), has only two. The water is expelled by the decanter coil together with the pomace, resulting in a wetter pomace that is much harder to process industrially. Many pomace oil extraction facilities refuse to work with these materials because the energy costs of drying the pomace for the hexane oil extraction often make the extraction process sub economical. In practice, then, the two phases decanter solves the phenol washing problem but increases the residue management problem. This residue management problem has been reduced by the collection of this wetter pomace and being transported to specialized facilities called extractors which heat the pomace between 45 °C and 50 °C and can extract up to a further 2 litres per 100 kilos of pomace using adapted two phase decanters. The two and a half phase oil decanter is a compromise between the two previous types of decanters. It separates the olive paste into the standard three phases, but has a smaller need for added water and also a smaller vegetation water output. Therefore, the water content of the obtained pomace comes very close to that of the standard three phase decanter, and the vegetation water output is relatively small, minimizing the residue management issues. Depending on the olives and processing, the Decanter or Tricanter can extract between 85 and 90% of the olive oil in the 1st extraction. The yield from olive oil manufacture can be increased even further with a 2nd extraction. The olive oil yield increases to as much as 96% by combining the 1st and 2nd extractions.

The Sinolea method to extract oil from the olives was introduced in 1972; in this process, rows of metal discs or plates are dipped into the paste; the oil preferentially wets and sticks to the metal and is removed with scrapers in a continuous process. It is based on the different surface tension of the vegetation water and the oil, these different physical behaviors allow the olive oil to adhere to a steel plaque while the other two phases remain behind. Sinolea works by continuously introducing several hundreds of steel plaques into the paste thus extracting the olive oil. This process is not completely efficient leaving a large quantity of oil still in the paste, so the remaining paste has to be processed by the standard modern method (industrial decanter).

Many oils are marketed as first cold pressed or cold extraction. "Cold" means no heat is added during extraction. "Pressed" means that the olives are crushed in a mill to extract the oil. In the EU, these designations are regulated by Article 5 of Commission Regulation (EC) No 1019/2002 of 13 June 2002 on marketing standards for olive oil. This article states that in order to use these designations the olive oil bottler must prove that the temperature of malaxation and extraction was under 27 °C (80 °F). For olive oil bottled outside EU countries, this regulation does not apply, and thus the consumer has no assurance that these statements are true. The temperature of malaxation and extraction is crucial due to its effect on olive oil quality. When high temperatures are applied, the more volatile aromas are lost and the rate of oil oxidation is increased, producing therefore lower quality oils. In addition, the chemical content of the polyphenols, antioxidants, and vitamins present in the oil is reduced by higher temperatures. The temperature is adjusted basically by controlling the temperature of the water added during these two steps. High temperatures are used to increase the yield of olive oil obtained from the paste.

Some producers, in order to maximise product quality, choose to combine the traditional grinding method, the stone mill, with a modern decanter. This technique produces more selective grinding of the olives, reduces the malaxation time olive paste, and avoids the complicated cleaning of the olive press fibre disks. Because the use of the stone mill requires a loading and unloading phase, this extraction method is discontinuous, i. e., there are times when all the machinery is stopped, therefore it is generally not used on a large commercial scale, being applied only by small scale olive mills producing high quality olive oil.

High quality olive oil can be obtained by all the methods if proper measures are taken. Olive oil quality is equally dependent on the quality of the olives themselves and on the time they have to wait from harvesting to extraction, in addition to the extraction method itself. The two main agents that cause the degradation of olive oil are oxygen and light. Once an olive is harvested, it should be pressed within 24 hours. Oxidation begins immediately upon harvesting. In the period between harvest and grinding, the fruits' enzymes are very active and increasingly degrade the endogenous oil, and therefore oil obtained after a longer wait is of lower quality, presenting higher acidity (free fatty acids percentage). In addition, if additional oxygen is allowed to interact with the olive paste during the extraction process, the acidity level will increase further. Sealed extraction methods are best to prevent the continued introduction of oxygen, as well as light to the oil. After extraction is complete, in most cases unfiltered olive oil appears somewhat cloudy, mainly due to the presence of minute amounts of water and suspended solids of olive pulp and seed. This type of oil is therefore sometimes called cloudy or veiled olive oil. It is common practice that unfiltered olive oils are then "racked" for a time, i. e. stored in cool stainless steel silos with a conical bottom that are pumped free of oxygen to enable the precipitation and separation of the two phases and facilitate later filtration; it will also contribute in the integrity and stability of the oil.