Coffee roasting

Process of heating green coffee beans

Roasting coffee transforms the chemical and physical properties of green coffee beans into roasted coffee products. The roasting process is what produces the characteristic flavor of coffee by causing the green coffee beans to change in taste. Unroasted beans contain similar if not higher levels of acids, protein, sugars, and caffeine as those that have been roasted, but lack the taste of roasted coffee beans due to the Maillard and other chemical reactions that occur during roasting. Coffee tends to be roasted close to where it will be consumed, as green coffee is more stable than roasted beans. The vast majority of coffee is roasted commercially on a large scale, but small scale commercial roasting has grown significantly with the trend toward "single origin" coffees served at specialty shops. Some coffee drinkers even roast coffee at home as a hobby in order to both experiment with the flavor profile of the beans and ensure the freshest possible roasted coffee. The first recorded implements for roasting coffee beans were thin pans made from metal or porcelain, used in the 15th century in the Ottoman Empire and Greater Persia. In the 19th century, various patents were awarded in the U. S. and Europe for commercial roasters, to allow for large batches of coffee. In the 1950s just as instant coffee was becoming a popular coffee drink, speciality coffee houses began opening to cater to the connoisseur, offering a more traditionally brewed beverage. In the 1970s, more speciality coffee houses were founded, ones that offered a variety of roasts and beans from around the world. In the 1980s and 1990s, the gourmet coffee industry experienced great growth. This trend continued into the 21st century.

The first known implements for roasting coffee beans were thin, circular, often perforated pans made from metal or porcelain, used in the 15th century in the Ottoman Empire and Greater Persia. This type of shallow, dished pan was equipped with a long handle so that it could be held over a brazier (a container of hot coals) until the coffee was roasted. The beans were stirred with a slender spoon. Only a small amount of beans could be heated at one time. The first cylinder roaster with a crank to keep the beans in motion appeared in Cairo around 1650. It was made of metal, most commonly tinned copper or cast iron, and was held over a brazier or open fire. French, Dutch and Italian variations of this design quickly appeared. These proved popular over the next century in Europe, England and the American colonies. In the 19th century, various patents were awarded in the U. S. and Europe for commercial roasters, to allow for large batches of coffee. Nevertheless, home roasting continued to be popular. A man working at a commercial roasting plant beginning in the 1850s in St. Louis, Missouri, said that "selling roasted coffee was up hill work, as everyone roasted coffee in the kitchen oven." Appliances catering to the home roaster were developed; in 1849 a spherical coffee roaster was invented in Cincinnati, Ohio, for use on the top of a wood fired kitchen stove, fitted into a burner opening. Green beans were available at the local general store, or even through mail order. much like the innovations of inventors in Emmerich am Rhein greatly advanced commercial coffee roasting in Germany. As well, the 1864 marketing breakthrough of the Arbuckle Brothers in Philadelphia, introducing the convenient one pound (0.45 kg) paper bag of roasted coffee, brought success and imitators. From that time commercially roasted coffee grew in popularity until it gradually overtook home roasting during the 1900s in America. In 1903 and 1906 the first electric roasters were patented in the U. S. and Germany, respectively; these commercial devices eliminated the problem of smoke or fuel vapor imparting a bad taste to the coffee. In France, the home roaster did not yield to the commercial roaster until after the 1920s, especially in rural areas. Coffee was roasted to a dark color in small batches at home and by shopkeepers, using a variety of appliances including ones with a rotating cylinder of glass, sheet iron or wire mesh, and ones driven by hand, clockwork or electric motor. Because of the smoke and blowing chaff, country dwellers generally roasted outdoors. In the 1950s just as instant coffee was becoming a popular coffee drink, speciality coffee houses began opening to cater to the connoisseur, offering a more traditionally brewed beverage. In the 1970s, more speciality coffee houses were founded, ones that offered a variety of roasts and beans from around the world. In the 1980s and 1990s, the gourmet coffee industry experienced great growth. Through the 1970s and 1980s, the Siemens Sirocco home roaster was made in West Germany and marketed globally. It was a small fluid bed roaster made for the home enthusiast. The product was named after a commercial hot air roasting process which itself was named after the hot Sahara winds called sirocco. In 1976, chemical engineer Michael Sivetz patented a competing hot air design for manufacture in the U. S.; this became popular as an economical alternative. Sivetz called for the home roaster to focus on the quality of the bean. From 1986 through 1999 there was a surge in the number of patents filed for home roasting appliances. In the 1990s, more electric home roasting equipment became available, including drum roasters, and variations on the fluid bed roaster. By 2001, gourmet coffee aficionados were using the internet to purchase green estate grown beans for delivery by mail.

The coffee roasting process follows coffee processing and precedes coffee brewing. It consists essentially of sorting, roasting, cooling, and packaging but can also include grinding. Bags of green coffee beans are hand or machine opened, dumped into a hopper, and screened to remove debris. The green beans are then weighed and transferred manually, by belt, or pneumatic conveyor to storage hoppers. From the storage hoppers, the green beans are conveyed to the roaster. Initially, the process is endothermic (absorbing heat), but at around it becomes exothermic (giving off heat). For the roaster, this means that the beans are heating themselves and an adjustment of the roaster's heat source might be required. At the end of the roasting cycle, the roasted beans are dumped from the roasting chamber and are typically cooled by air or water quenching. During the roasting process, coffee beans lose 15 to 18% of their mass due mainly to the loss of water but also to volatile compounds. Although the beans experience a weight loss, the size of the beans double during the roasting process due to the physical expansion caused by an increase in internal pressure from vaporized water. Green coffee can contain reasonable quantities of simple sugars. Sugars are quite reactive at roasting temperatures and, once the water has evaporated out of the bean, the sugars can begin to react to the heat in different ways. Some go through caramelization reactions, creating the caramel notes found in certain coffees. There are several traditional variations to coffee roasting in different parts of the world. For example, in Vietnam coffee is often coated with oil (traditionally clarified butter) and a small amount of sugar prior to roasting to produce a "butter roast". The roasting process results in an additional caramelized coating on the beans.

The most common roasting machines are of two basic types: drum and hot air, although there are others including packed bed, tangential and centrifugal roasters. Roasters can operate in either batch or continuous modes. Home roasters are also available. Drum machines consist of horizontal rotating drums that tumble the green coffee beans in a heated environment. The heat source can be supplied by natural gas, liquefied petroleum gas (LPG), electricity, or even wood. The most common employ indirectly heated drums where the heat source is under the drum. Direct fired roasters are roasters in which a flame contacts the beans inside the drum; very few of these machines are still in operation. Fluid bed or hot air roasters force heated air through a screen or perforated plate under the coffee beans with sufficient force to lift the beans. Heat is transferred to the beans as they tumble and circulate within this fluidized bed.

Some coffee roasters use names for the various degrees of roast, such as "city roast" and "French roast", for the internal bean temperatures found during roasting. Recipes known as "roast profiles" indicate how to achieve flavor characteristics. Any number of factors may help a person determine the best profile to use, such as the coffee's origin, variety, processing method, moisture content, bean density, or desired flavor characteristics. A roast profile can be presented as a graph showing time on one axis and temperature on the other, which can be recorded manually or using computer software and data loggers linked to temperature probes inside various parts of the roaster. One method of determining the degree of roast is to evaluate the bean's color. As the coffee absorbs heat, the color shifts to yellow and then to increasingly darker shades of brown. During the later stages of roasting, oils appear on the surface of the bean. The roast will continue to darken until it is removed from the heat source. It is common for roasters to use a combination of temperature, smell, color, and sound to monitor the roasting process. The famous Italian roaster Gianni Frasi explains how artisanal roasting is fundamental in order to obtain a high quality coffee ("immersion in direct flame is purification, it makes a dead bean alive", "the bean's dignity can only be guaranteed by an open flame"). Also according to Frasi, the bean can be defined as perfectly toasted when it takes on a particular "friar's tunic" color nuance which can only be obtained in a precise instant of the process and which the craftsman must be able to grasp by sight. This particular coloring is proof that all the potential aromas of the green bean have been released. The craft system was codified by Italian author Luca Farinotti in his 2019 award winning book World and restaurant. There are two events called "cracks" that roasters listen for. At approximately , the coffee will emit a cracking sound. This point is referred to as "first crack", marking the beginnings of a very light roast. At first crack, a large amount of the coffee's moisture has been evaporated and the beans will begin to increase in size. When the coffee reaches approximately , it emits a "second crack". This sound represents the structure of the coffee becoming brittle and fracturing as the bean continues to swell and enlarge from internal pressure. Lipids present inside the coffee seed liquify from heat and pressure built up in the bean. These lipids can often be seen on the bean surface. An oily coating is more prevalent with darker roasts. These images depict samples taken from the same batch of a typical Brazilian green coffee at various bean temperatures with their subjective roast names and descriptions.

Home roasting is the process of roasting small batches of green coffee beans for personal consumption. Even after the turn of the 20th century, it was more common for at home coffee drinkers to roast their coffee in their residence than it was to buy pre roasted coffee. Later, home roasting faded in popularity with the rise of the commercial coffee roasting companies. In recent years home roasting of coffee has seen a revival. In some cases there is an economic advantage, but primarily it is a means to achieve finer control over the quality and characteristics of the finished product.

Extending the shelf life of roasted coffee relies on maintaining an optimum environment to protect it from exposure to heat, oxygen, and light. Roasted coffee has an optimal typical shelf life of two weeks, and ground coffee about 15 minutes. Without some sort of preservation method, coffee becomes stale. The first large scale preservation technique was vacuum packing in cans. However, because coffee emits CO2 after roasting, coffee to be vacuum packed must be allowed to de gas for several days before it is sealed. To allow more immediate packaging, pressurized canisters or foil lined bags with pressure relief valves can be used. Refrigeration and freezing retards the staling process. Roasted whole beans can be considered fresh for up to one month if kept cool. Once coffee is ground it is best used immediately.

Particulate matter (PM), volatile organic compounds (VOC), organic acids, and combustion products are the principal emissions from coffee processing. Several operations are sources of PM emissions, including the cleaning and destoning equipment, roaster, cooler, and instant coffee drying equipment. The roaster is the main source of gaseous pollutants, including alcohols, aldehydes, organic acids, and nitrogen and sulfur compounds. Because roasters are typically heated by combustion of natural gas, carbon monoxide (CO) and carbon dioxide (CO2) emissions result from fuel combustion. Decaffeination and instant coffee extraction and drying operations may also be sources of small amounts of VOC. Emissions from the grinding and packaging operations typically are not vented to the atmosphere. Particulate matter emissions from the roasting and cooling operations are typically ducted to cyclones before being emitted to the atmosphere. Gaseous emissions from roasting operations are typically ducted to a thermal oxidiser or thermal catalytic oxidiser following PM removal by a cyclone. Some facilities use the burners that heat the roaster as thermal oxidisers. However, separate thermal oxidisers are more efficient because the desired operating temperature is typically , which is more than the maximum temperature of most roasters. Some facilities use thermal catalytic oxidizers, which require lower operating temperatures to achieve control efficiencies that are equivalent to standard thermal oxidisers. Catalysts are also used to improve the control efficiency of systems in which the roaster exhaust is ducted to the burners that heat the roaster. Emissions from spray dryers are typically controlled by a cyclone followed by a wet scrubber.