Фотогравюра: История и возрождение техники фотографической печати

Photographic printing technique

Photogravure (in French héliogravure) is a process for printing photographs, also sometimes used for reproductive intaglio printmaking. It is a photo mechanical process whereby a copper plate is grained (adding a pattern to the plate) and then coated with a light sensitive gelatin tissue which had been exposed to a film positive, and then etched, resulting in a high quality intaglio plate that can reproduce detailed continuous tones of a photograph. The process was important in 19th century photography, but by the 20th century was only used by some fine art photographers. By the mid century it was almost extinct, but has seen a limited revival.

The earliest forms of photogravure were developed by two original pioneers of photography itself, first Nicéphore Niépce in France in the 1820s, and later Henry Fox Talbot in England. Niépce was seeking a means to create photographic images on plates that could then be etched and used to make prints on paper with a traditional printing press. He used prints (engravings etc. ), waxing the paper to make it translucent, then laying this on a copper plate coated with light sensitive bitumen. Niépce's early images were among the first photographs, pre dating daguerreotypes and the later wet collodion photographic process. But the process was little used, not least because the original engraving was all but destroyed. But once a "transparent photographic positive" became possible, interest revived. Talbot, inventor of the calotype paper negative process, wanted to make paper prints that would not fade. He worked on his photomechanical process in the 1850s and patented it in 1852 ('photographic engraving') and 1858 ('photoglyphic engraving'). Photogravure in its mature form was developed in 1878 by Czech painter Karel Klíč, who built on Talbot's research. :4 This process, the one still in use today, is called the Talbot Klič process. and for photo reproduction of works from other media such as paintings. From the 1880s, the Talbot Klič process was used commercially for very high quality reproductions of old master prints, excelling in capturing variations in tone. This publication also featured the photogravures of Alvin Langdon Coburn who was a fine gravure printer and envisioned his photographic work as gravures rather than other photo based processes. The speed and convenience of silver gelatin photography eventually displaced photogravure which fell into disuse after the Edward S. Curtis gravures in the 1920s. One of the last major portfolios of fine art photogravures was Paul Strand's Photographs from Mexico from 1940, reissued as The Mexican Portfolio in 1967 by DeCapo Press. Many years later, photogravure has experienced a revival in the hands of Aperture and Jon Goodman, who studied it in Europe. Photogravure is now actively practiced in several dozen workshops around the world. Contemporary artists working in the medium include Sama Alshaibi.

Photogravure registers a wide variety of tones, through the transfer of etching ink from an etched copper plate to special dampened paper run through an etching press. The unique tonal range comes from photogravure's variable depth of etch, that is, the shadows are etched many times deeper than the highlights. Unlike half tone processes which vary the size of dot, the depth of ink wells is varied in a photogravure plate. The human eye resolves these fine variations into a continuous tone image. Photogravure is distinguished from rotogravure in that photogravure uses a flat copper plate etched rather deeply and printed by hand, while in rotogravure, as the name implies, a rotary cylinder is only lightly etched, and it is a factory printing process for newspapers, magazines, and packaging. In French, the correct term for photogravure is héliogravure, while the French term photogravure refers to any photo based etching technique.

Printing a photogravure is similar to printing any other intaglio plate, especially a finely etched aquatint. A stiff, oily intaglio printing ink is applied to the whole surface of the plate with a rubber brayer, or a small, stiff squeegee, or a rolled tamper. The plate is then gently wiped with tarlatans to remove the excess ink and drive it into the recesses (wells). It is finally wiped with the fatty part of the palm of the hand in quick glancing strokes. This removes all remaining ink from the polished highlights and high points and leaves ink only in the etched recesses. After the edges are cleaned, the plate is placed on the printing bed of an intaglio press. It is covered with a sheet of dampened rag paper and then two to three layers of thin wool blankets. It is then run through the press at high pressure. The high pressure pushes the fibers of the dampened paper into the wells of the plate which then transfers the ink onto the paper thereby creating the impression. The paper is carefully peeled off the plate and placed between blotters and weighted so it will dry flat. The plate can now be re inked for another impression or it can be cleaned for storage. Macdermid Autotype, the last manufacturer of the gelatin pigment paper (tissue) needed to make traditional copper plate photogravure, announced the end of their production in August 2009. Since then, other manufacturers, including Bostick & Sullivan, Phoenix Gravure, and others in India, Taiwan, and Japan have begun supplying gelatin pigment paper (resist tissue) to the market. These products are used by practitioners of traditional photogravure etching and by commercial printers.

Donald Farnsworth at the art workshop Magnolia Editions developed a digital direct to plate photogravure process that does not use gelatin. Instead, a series of 'masks' (layers of resist) are printed onto a copper plate using a flatbed UV cured acrylic printer: "The flatbed printer allows us to etch a stochastic [random] dot pattern into the plate in a completely controlled, precise way  This process is an inversion of the traditional photogravure method, where you're etching through a sheet of gelatin, and gradually the gelatin is getting thinner and more acid reaches the plate, so the last thing that's etched are the light tones." Instead, the digital direct to plate method requires that the light values be etched first; then the printer is used to lay down a new layer of ink onto the plate between acid baths, masking out the lighter values to protect them from subsequent etches. The initial mask looks like it has barely been printed; the masks grow in density until the plate eventually appears almost completely black. In another variation of the traditional process, where the acid baths are increasingly watered down as the process unfolds, the direct to plate process begins with a weak bath and is gradually etched in baths which are increasingly acidic.

Photopolymer plates, usually used for relief and letterpress printing, can be used to make photogravure plates. These polymer plates, when developed, are a hard plastic, which allows for fewer impressions to be made. Some feel that they rival the quality of traditional copper plate photogravure, while others find that the lack of differential depth in the polymer coating compromises quality. The process involves a series of exposures of the polymer plate. First, it is exposed under strong light with a random dot screen placed on top of it (called an aquatint screen in fine art printing or a stochastic screen in commercial printing). Next, the plate is exposed to a positive transparency of an image. This transparency can be a continuous tone positive on film, but is most often made as a digital 'positive' (made in the same way as a digital negative) printed with an inkjet printer. The plate is then developed; for most types and brands of plates, this is done in water. After proper drying and curing, the plate can be inked and printed. The dual exposures produce an "etched" polymer plate with many thousands of indentations of varying depth which hold ink, which in turn are transferred as a continuous tone image to a sheet of paper. Depending on the quality, the resulting print may look similar to or the same as those produced with the traditional photogravure process, though without the same amount of three dimensional depth on the surface of the plate, and arguably, the print itself. Two polymer plates commonly in use are Printight plates made by the Toyobo Corporation and Solarplates.