Lotus Europa: Екі таңдаулы автомобиль

Two automobiles by Lotus

The Lotus Europa name is used on two distinct mid engine GT cars built by British automobile manufacturer Lotus Cars. The original Europa and its variants comprise the Lotus Types 46, 47, 54, 65 and 74, and were produced between 1966 and 1975. The name was later revived in the Type 121 Europa S, a sports car based on the Lotus Elise produced from 2006 to 2010.

By the mid 1960s, the mid engine vehicle configuration was well established as the optimal design for Grand Prix cars, however almost no road vehicles yet used this arrangement. Lotus planned the Europa to be a volume produced, two seater mid engine sports coupe built to reasonable cost, quite an ambitious goal for the time. Like all Lotus vehicles of the era, the Europa was designed and built following Colin Chapman's oft stated philosophy of automotive design: "Simplify, then add lightness". To this end, a number of ingenious design approaches were made by Lotus to allow it to economically overcome the many challenges presented by the novel mid engine arrangement. Production of the original Lotus Europa ceased in 1975, with a total of 9,230 cars of all models having been built.

The Europa used a lightweight, folded and welded "minimalist" boxed steel backbone chassis with a fibreglass moulded body, a combination that was first used by Lotus founder Colin Chapman in the Lotus Elan launched in 1962. Earliest versions of the Europa had the body fully bonded to the chassis for maximum structural stiffness, however this was soon changed to a bolted on body to allow normal chassis and body repairs to be made. Unlike the Elan, the Europa had no front mounted engine or gearbox to accommodate, and so the Europa's main chassis member ran straight forward to intersect a large box section cross beam running across the car between the front suspension points. At the rear, the chassis split into a "U" shape behind the cabin to accommodate the combined engine, transmission and final drive components, and to support the rear suspension.

The sourcing of suitable engine, gearbox and final drive components was considered critical to the success of delivering a low cost mid engine vehicle. Chapman was keen to diversify beyond the Ford components heavily used in earlier Lotus vehicles, and settled on using the engine and combined transmission/final drive transaxle units recently released by Renault for their 16. The Renault engine was a light and modern design, while the matching Renault 16 transaxle seemed almost ideal for the Europa project. In the Renault, the transaxle sat ahead of the engine, driving the front wheels. By relocating the combined engine/transaxle unit to the rear of the car and rotating it 180 degrees in plan, Lotus could obtain a ready made modern mid engine configuration albeit one with four reverse gears. By repositioning the differential crownwheel within the final drive assembly (made possible by the symmetrical split case), the direction of rotation of the output shafts was reversed, thus correcting this shortcoming. The Renault 16's engine's design met Lotus's requirements. It used an aluminium block with cast iron cylinder liners, which saved appreciable weight compared to the cast iron blocks more common at the time. Its overhead valve design had the camshaft located high up in the block, resulting in a compact valve train well suited for high rpm operation. Most importantly, all the engine ancillaries (water pump, belt drives, alternator) were driven off a v belt pulley fixed to the transaxle end of the camshaft instead of being driven by the engine's crankshaft. When fitted to the Europa, this pulley location put all the engine's ancillaries at its rear face giving easy access for maintenance, rather than them being located against the vehicle's bulkhead as for most conventional engines. For Lotus' use, the Renault engine was given a number of key improvements, including a higher compression ratio (10.25 instead of 8.6), larger inlet valves, revised valve timings, dual valve springs and a twin barrel carburettor. These changes lifted the engine's power by 23% from at 5,000 rpm to at 6,000 rpm. For US export, a de tuned version with a maximum output of at 6,000 rpm was fitted. Later, Europa models were fitted with the same Ford based Lotus TwinCam engine used in the Elan range since 1962. This was a sophisticated, twin overhead cam, 8 valve high performance engine rated at in original (Euro) specification (later uprated to in "big valve" form). It was reported that Lotus initially delayed its introduction in the Europa until they were confident in the strength of the Renault transaxle. The twin cam engine first appeared in the Europa engine bay in mid 1971 (in Europe) and early 1972 (in North America). In the Europa, the vertical "strut" element pivots on the wheel hub at its lower end and doesn't control wheel camber angle as in earlier Lotus designs. Wheel location and alignment is controlled instead by interaction between a fixed length, articulated driveshaft top link, a simple tubular lower link, and a large box section radius arm running diagonally forward to the chassis. The car's subsequent resulting handling prompted automotive writers to describe the Europa as the nearest thing to a Formula car for the road.

The Series 1 or S1 Europa (also known as Lotus Type 46) was announced for sale to European markets on 20 December 1966. The first cars were delivered in France in February 1967. Volkswagen owned the rights to the Europa name in Germany, so cars for sale in Germany were badged Europe rather than Europa. The S1 was fitted with a modified Renault 16 1,470 cc inline four engine and a 4 speed gearbox. The engine was a special version (as opposed to the generated in standard form). Lotus adapted the affordable but lightweight Renault engine and gearbox to the revolutionary Europa longitudinal mid engined layout, inverting the gearbox's crown wheel on its pinion gear to avoid having four reverse gears. The S1 weighed Autocar magazine achieved a top speed of , and recorded a 0–60 mph acceleration time of 9.3 seconds. Of particular note, in excess of 0.9 g (8 m/s²) lateral acceleration was consistently achieved by Car magazine on road tyres of that era. Only 296 examples of the S1 were manufactured (chassis numbers from 460001 to 460296). These cars had extremely light and minimalist construction, with fixed side windows, fixed seats (adjustable pedals needing the use of tools), no door handles, no internal door covers, and an aluminum dashboard. The steel chassis central beam was sandwiched (incorporated) within the fibreglass bodywork, thus reinforcing stiffness, but making repair rather complicated. Series 1A and B (around 350 built) had removable side windows, wooden dashboard, and internal door panel covers which could accommodate the windows once taken off. Series 1B had a redesigned rear panel, with new, rectangular light clusters. Including the S1A and S1B (which incorporated some of the later S2 changes) variations, 644 Europa S1s were manufactured.

The Europa Series 2, or Lotus Type 54, was introduced in April 1968 (approximately chassis number 0645 onwards). The S2 used the same 1,470 cc Renault engine and mechanical components as the earlier Series 1, but added a number of key refinements including opening electric windows, adjustable seats, a new fully carpeted interior and a polished wooden fascia panel for the dashboard. The most significant change was the switch from fully bonded construction to the use of bolt fasteners to attach the fibreglass body to the backbone steel frame. While reducing the torsional and flexural stiffness somewhat, the use of a separable body was welcomed by the automotive insurance industry as it greatly reduced the complexity and cost of making repairs to the vehicle. From early 1969, secondary front indicator lamp nacelles were added between the headlights, and larger door handles were used in place of the S1's push button items. During 1968 a number of Europas (and Elans) were produced bearing black and silver Lotus badges on the nose and steering wheel in place of the customary yellow and green ones. The official Lotus Cars website states these "black badge" vehicles were to commemorate the death earlier in 1968 of Jim Clark, Lotus's champion Formula One driver, however this is debated by other sources. Contemporary road tests for the Europa S2 recorded a top speed around 120 mph (195 km/h), 0 60 mph acceleration times of 9.3 seconds, standing 1/4 mile times of around 16.7 seconds, and an overall economy of around 30 mpg (9.4 L/100 km).

A small number of Series 2 vehicles were modified to be "federalized" for export to the United States. These Federal Type 54s had the low front fenders (guards) of the European model and the larger 1,565 cc engine of the later Lotus Type 65. In 1969–70, the Type 65 (also known as S2 Federal) was introduced specifically for export to the U. S., with additional changes to the body, chassis, suspension and the powerplant to better comply with U. S. D. O. T. standards. Among the changes, the engine was a slightly modified emission controlled Renault 16TL 1,565 cc unit rated at 80 hp rather than the 1,470 cc engine of the Type 54. The front suspension was changed to make the front end of the car taller along with taller front fenders to raise the headlamps. Road & Track magazine tested the Federal S2 and recorded 0 60 mph acceleration time of 9.6 seconds with a top speed of
In total, Lotus produced 3,615 Europa S2s.

In 1971, the Type 74 Europa Twin Cam was made available to the public, with a 105 hp 1,557 cc Lotus Ford Twin Cam engine (113 hp US "Federal" version with standard emissions control and Big Valve engine with Stromberg carburetors, until the end of production) and a re designed bodyshell to improve rearward visibility. Initially it was available with the same gearbox as the earlier cars, once the supply had been exhausted in 1972 a new stronger Renault four speed gearbox (Type 352) was introduced. Mike Kimberley, who rose to become chief executive of Group Lotus, then a new engineer at Lotus, was appointed Chief Engineer of the Europa TC project. 1,580 cars were shipped as Europa "Twin Cam" before Lotus switched to a 126 hp "Big Valve" version of the engine. In Europe and rest of the world markets, the Big Valve "Europa Special" version was aspirated by a Dell'Orto carburettored version of the same engine; it also offered a new Renault five speed (Type 365) gearbox option. It weighed ; Motor magazine tested a UK Special to a top speed of , recorded a 0–60 mph acceleration time in 6.6 seconds, and ran the 1/4 mile in 14.9 seconds. In the US version of the Europa Special, where the Federalized version of the Big Valve had already been introduced earlier in the Twin Cam model, the only changes were larger brakes and the optional five speed transmission which would become standard on the special in 1974. Introduced in September 1972, the first 100 Lotus Europa JPS Specials were badged and painted to honour Team Lotus's F1 season of 1972 F1 World Championship title win with John Player Special as the team’s sponsor. All with a five speed gearbox and Big Valve engine the original Specials were painted black with a gold pin stripe matching the livery of the GP cars – plus a numbered JPS dashboard badge. These were the first John Player Special commemorative Lotus production vehicles. The "Special" name and colour scheme was planned to be dropped after the commemorative cars, with Lotus reverting to the Twin Cam name, but such was the positive reaction to the new car that the name and the black and gold pin stripe colour scheme continued until the end of Europa production although colours other than black were made available. In the end the numbered dashboard plaque distinguished the first, original, 100 JPS cars from other black Europa Specials. In total 4,710 Type 74s were produced, of which 3,130 were badged "Specials".

Although the original Europa was intended as a clubman's sports racer to replace the Lotus 7, it was realised that the car would be uncompetitive with the Renault engines available. A decision was therefore made to manufacture a specialist race car based on the Europa to be raced by Team Lotus and sold to private entrants. Although the very first Type 47 was based on a modified Europa, all subsequent cars were produced entirely by Lotus Components rather than the main factory. Launched at the same time as the S1 Europa, the body of the 47 was thinner than the standard Europa and with larger wheel arches. Side vents into the engine bay were added after the first few cars experienced problems with engine bay temperature. The engine, gearbox and rear suspension were completely different from the standard Europa and were taken in their entirety from the Lotus 23/Lotus 22 Formula Junior cars with a Lotus Ford Twin Cam based 165 hp (123 kW) 1,594 cc Cosworth Mk. XIII dry sump engine, and a Hewland FT 200 5 speed gearbox and suspension with reversed bottom wishbone, top link and dual radius arms. The front upright was specially cast in common with the F2 version of Lotus 41X to accommodate larger Girling brakes for the later 47A model (which had the Alfa Romeo tail lamp shared with the Europa S2) with reinforced front frame. The Type 47 exact production numbers are unknown, the last car was 47GT 85 but it is unlikely that 85 47GT's were produced, estimates vary from 55 to 68 during the years 1966–70. Although the 47GT is the best known, a few 47F's were produced, these had the detachable body similar to the S2 Europa, but retaining the large wheel arches and side vents of the 47GT. Fitted with a tuned Ford cross flow engine but with the Renault gearbox and rear suspension of the Europa. At the request of parts supplier GKN, Lotus built the 47D as a show car. The 47D has a slightly enlarged chassis and body to fit a Rover V8 engine. At the time the 47D was built, it was capable of in 10 seconds. As a mobile test bed for the new 2 litre Lotus 907 engine being developed for the forthcoming Elite and Eclat, the Type 62 was produced. Only two such cars were ever made. These were space frame cars with F1 suspension to handle the 240 hp power output from the engine. Although deliberately made to resemble the Europa, in practice the only connection to the Europa was a few of the Europa's body panels. It won its class in its first event the 1969 BOAC 500 at Brands Hatch with John Miles and Brian Muir at the wheel. Replica 47's and 62's are bespoke manufactured by Banks Europa Engineering, in several variations.

Throughout its life, the Europa attracted the attention of many Lotus and non Lotus automotive customising businesses who offered "special" versions in small numbers to the public. Among these was the Swiss Lotus importer, who made two special versions of the S2 fitted with the Renault 16 TS type 807 engine, the "Europa Hemi 807" and the fuel injected "Europa Black Shadow 807". The Hemi 807 had SAE and could attain a speed of , while the Black Shadow had power output of The Black Shadow also received a five speed gearbox. These cars had a wider track, special wheels and stickers, white indicator lights up front, and featured extractor vents high on the side panel behind the rear door. The fuel injection system was from Kugelfischer. In 1971 two Lotus Hemi were entered as Group 4 GTS at the international hill climb race St. Ursanne Les Rangiers and Ollon Villars driven by the Swiss divers Oskar Bubeck and Alfons Tresch. Chip Foose the famous automobile pioneer of United States also modified and restored a Lotus Europa for Episode 6 of the season 11 of his popular show "Overhaulin'". It was one of the most time consuming and complicated build of the show, where a brand new 1.8 litre four cylinder engine from an Elise was fitted into the car, while the power is handled by Porsche Boxster transmission. The bumpers were also tucked in signature Foose style. in 1972, a Bristol based company called GS Cars has produced a variant of the Lotus Europa. This version is based on the standard Lotus Europa Twin Cam, but has new bodywork which bears some resemblance to the Maserati Merak. The GS Lotus Europa was limited to 17 units. However, only 5 are known to still exist.

In 2005, Lotus released images of a new GT type car called the Lotus Europa S. Based on the Lotus Elise, the car was officially introduced at the 2006 Geneva Motor Show. Production commenced in July 2006 and continued until 2010. The engine was a turbocharged four cylinder, rated at at 5,400 rpm, with a maximum torque of at 5,400 rpm. The Europa S could accelerate from in 5.6 seconds ( in 5.8 seconds), with a maximum speed of Lotus did not export the Europa S to the United States. Despite this, the American manufacturer Dodge developed an electric vehicle based on the Europa, known as the Dodge Circuit, which it planned to bring to the US market by 2010, but the project was cancelled in May 2009. The Europa SE was unveiled at the Geneva International Motor Show on 5 March 2008. The SE was an upgraded model with more comfort in mind, intended to bring in more customers. The SE has the same engine as the S but it was modified to bring power to and torque to .