Введение
Констрикторный узел
The constrictor knot is one of the most effective binding knots. Although Ashley seemed to imply that he had invented the constrictor knot over 25 years before publishing The Ashley Book of Knots,
Although the description is not entirely without ambiguity, the constrictor knot is thought to have appeared under the name "gunner's knot" in the 1866 work The Book of Knots, written under the pseudonym Tom Bowling. The knot is described in relation to the clove hitch, which he illustrated and called the "builder's knot". He wrote, "The Gunner's knot (of which we do not give a diagram) only differs from the builder's knot, by the ends of the cords being simply knotted before being brought from under the loop which crosses them." But Bowling is simply an extraction and translation of the knotting work contained in the huge French Traite de L'Art de la Charpenterie, first published in 1841, which says "Le nœud de bombardier, que nous n'avons point figuré, ne differe du nœud d'artificier qu'en ce que les bouts du cordage sont croisés en nœud simple, avant de sortir de dessous la ganse qui les croise, fig.46." When J. T. Burgess copied from Bowling, he changed this text to merely state "when the ends are knotted, the builder's knot becomes the gunner's Knot." Although a clove hitch with knotted ends is a workable binding knot, Burgess was not actually describing the constrictor knot. In 1917, A. Hyatt Verrill illustrated Burgess's clove hitch variation in Knots, Splices and Rope Work. The constrictor knot was clearly described but not pictured as the "timmerknut" ("timber knot") in the 1916 (2nd) edition of the Swedish book Om Knutar ("On Knots") by Hjalmar Öhrvall. Finnish scout leader Martta Ropponen presented the knot in her 1931 scouting handbook Solmukirja ("Knot Book"), one of the first published works known to contain an illustration of the constrictor knot. Make a turn around the object and bring the working end back over the standing part. Continue around behind the object. Pass the working end over the standing part and then under the riding turn and standing part, forming an overhand knot under a riding turn. Be sure the ends emerge between the two turns as shown. Pull firmly on the ends to tighten. There are also at least three methods to tie the constrictor knot in the bight and slip it over the end of an object to be bound.
Констрикторный узел – один из самых эффективных связывающих узлов. Хотя Эшли, по-видимому, намекал, что он изобрел констрикторный узел более чем за 25 лет до публикации «Книги узлов Эшли», описание не совсем однозначно, однако считается, что констрикторный узел впервые появился под названием «пушечный узел» в работе 1866 года «Книга узлов», написанной под псевдонимом Том Боулинг. Узел описан в связи с гвоздевой петлей, которую автор проиллюстрировал и назвал «узлом строителя». Он писал: «Пушечный узел (схему которого мы не приводим) отличается от узла строителя лишь тем, что концы веревок просто завязаны в узел, прежде чем их выводят из-под петли, которая их пересекает». Но Боулинг лишь извлек и перевел работы по вязанию узлов, содержащиеся в огромном французском трактате «Искусство столярного дела», впервые опубликованном в 1841 году, где сказано: «Узел бомбардира, который мы не изображаем, отличается от узла артиллериста только тем, что концы веревки перекрещены простым узлом, прежде чем выйти из-под обвязки, которая их пересекает, рис. 46». Когда Дж. Т. Берджесс переписал текст из Боулинга, он изменил его, сведя к простому утверждению: «Когда концы завязаны, узел строителя становится пушечным узлом». Хотя гвоздевая петля с завязанными концами является работоспособным связывающим узлом, Берджесс на самом деле не описывал констрикторный узел. В 1917 году А. Хайат Веррилл проиллюстрировал вариацию гвоздевой петли Берджесса в книге «Узлы, такелажные работы и плетение канатов». Констрикторный узел был четко описан, но не изображен как «timmerknut» («деревянный узел») в 1916 году (2-е издание) шведской книги Хьялмара Эрвальла «Om Knutar» («Об узлах»). Финский скаутский лидер Марта Роппонен представила узел в своем скаутском справочнике 1931 года «Solmukirja» («Книга узлов»), одной из первых опубликованных работ, содержащей иллюстрацию констрикторного узла. Сделайте оборот вокруг объекта и верните рабочий конец обратно на стоячий конец. Продолжайте движение за объектом. Пропустите рабочий конец поверх стоячего конца, а затем под ходовой оборот и стоячий конец, образуя простой узел под ходовым оборотом. Убедитесь, что концы выходят между двумя оборотами, как показано на рисунке. Плотно потяните за концы, чтобы затянуть узел. Существует также как минимум три способа завязать констрикторный узел в петле и надеть его на конец связываемого объекта.
The constrictor knot is one of the most effective binding knots. Although Ashley seemed to imply that he had invented the constrictor knot over 25 years before publishing The Ashley Book of Knots,
Although the description is not entirely without ambiguity, the constrictor knot is thought to have appeared under the name "gunner's knot" in the 1866 work The Book of Knots, written under the pseudonym Tom Bowling. The knot is described in relation to the clove hitch, which he illustrated and called the "builder's knot". He wrote, "The Gunner's knot (of which we do not give a diagram) only differs from the builder's knot, by the ends of the cords being simply knotted before being brought from under the loop which crosses them." But Bowling is simply an extraction and translation of the knotting work contained in the huge French Traite de L'Art de la Charpenterie, first published in 1841, which says "Le nœud de bombardier, que nous n'avons point figuré, ne differe du nœud d'artificier qu'en ce que les bouts du cordage sont croisés en nœud simple, avant de sortir de dessous la ganse qui les croise, fig.46." When J. T. Burgess copied from Bowling, he changed this text to merely state "when the ends are knotted, the builder's knot becomes the gunner's Knot." Although a clove hitch with knotted ends is a workable binding knot, Burgess was not actually describing the constrictor knot. In 1917, A. Hyatt Verrill illustrated Burgess's clove hitch variation in Knots, Splices and Rope Work. The constrictor knot was clearly described but not pictured as the "timmerknut" ("timber knot") in the 1916 (2nd) edition of the Swedish book Om Knutar ("On Knots") by Hjalmar Öhrvall. Finnish scout leader Martta Ropponen presented the knot in her 1931 scouting handbook Solmukirja ("Knot Book"), one of the first published works known to contain an illustration of the constrictor knot. Make a turn around the object and bring the working end back over the standing part. Continue around behind the object. Pass the working end over the standing part and then under the riding turn and standing part, forming an overhand knot under a riding turn. Be sure the ends emerge between the two turns as shown. Pull firmly on the ends to tighten. There are also at least three methods to tie the constrictor knot in the bight and slip it over the end of an object to be bound.
Двойной узловой констриктор
Если требуется более прочный и надёжный узел, к базовому узлу можно добавить дополнительный оборот, чтобы сформировать двойной констриктор. Он особенно полезен при работе с очень скользким шпагатом, особенно вощёным. Этот узел также рекомендован в качестве хирургического узла для лигирования в человеческой и ветеринарной хирургии, где он показал себя значительно превосходящим любые обычно используемые узлы для лигирования. Известный мастер-риггер Брион Тосс говорит о констрикторе: "Знать этот узел – значит постоянно находить ему применение".
Безопасность
Констриктор и двойной констриктор чрезвычайно надежны при плотном обвязывании выпуклых предметов шнуром, подобранным для данной задачи. Если обвязываете предмет с не полностью выпуклыми или квадратными краями, расположите узел так, чтобы часть с простым узлом натягивалась на выпуклую часть или угол, а виток лежал прямо поверх него. В случаях, когда под узлом остаются зазоры и нет углов, можно закрепить констриктор дополнительным простым узлом, как в рифовом узле, для большей стабильности. Несмотря на эти рекомендации, констрикторные узлы лучше всего работают с полностью выпуклыми предметами. Если обвязываемый предмет (например, временно закрепленная веревка) заканчивается очень близко к месту обвязки констриктором, узел "боа" может оказаться более устойчивым решением.