Ағылшыншамен салыстырыңыз: абзацты басыңыз — түпнұсқа терезеде ашылады. Абзац астындағы EN түймесі оны мәтін ішінде көрсетеді.
Мазмұны
Кіріспе
Неміс зымырандық күшпен жұмыс істейтін ұшқышсыз кеме прототипі
German rocket powered interceptor prototype
Бахем Ба 349 Наттер (Colubridae) – Екінші дүниежүзілік соғыстағы неміс қорғаныс зымырандық күшпен жұмыс істейтін ұшқышсыз кеме, ол адам басқаратын жер-әуе зымыраны сияқты қолданылатын болған. Тік көтерілу арқылы әуежай қажеттілігі жойылды, ал одақтас бомбалаушыларға қарсы ұшудың көп бөлігі автопилотпен басқарылатын еді. Ұшқыштың басты міндеті – ұшақты нысанаға бағыттап, зымырандарын ату болды. Содан кейін ұшқыш пен зымыран қозғалтқышы бар фюзеляж бөлек парашюттармен қонды, ал ұшақтың алдыңғы бөлігі бір рет қолданылатын еді. 1945 жылдың 1 наурызында жасалған алғашқы және жалғыз тік көтерілу сынағы ұшқыш Лотар Сибердің қазасына әкеп соқты.
The Bachem Ba 349 Natter ([[Colubridae) was a World War II German point defence rocket powered interceptor, which was to be used in a very similar way to a manned surface to air missile. After a vertical take off, which eliminated the need for airfields, most of the flight to the Allied bombers was to be controlled by an autopilot. The primary role of the relatively untrained pilot was to aim the aircraft at its target bomber and fire its armament of rockets. The pilot and the fuselage containing the rocket engine would then land using separate parachutes, while the nose section was disposable. The first and only manned vertical take off flight, on 1 March 1945, ended in the death of the test pilot, Lothar Sieber.
Өмірбаян
1943 жылы одақтастар Германияның әуедегі басымдылығына күйреу қаупі төнді, сондықтан дағдарысты жеңу үшін радикалды жаңалықтар қажет болды. Жер-әуе зымырандары одақтастардың стратегиялық бомбалау шабуылына қарсы тұрудың үміт берерлік жолы болды; түрлі жобалар қолға алынды, бірақ бағыттау және нысананы табу жүйелеріндегі мәселелер олардың ешқайсысын операциялық деңгейге жеткізбеді. Зымыранды қысқа мерзімді соңғы жақындау кезеңінде қаруды басқара алатын ұшқышпен жабдықтау шешім ұсынды. 1944 жылдың басында Luftwaffe, "Төтенше күрес бағдарламасы" деген мағына беретін Jägernotprogramm аясында қарапайым нысананы қорғауға арналған ұшқышсыз аппараттарға тапсырыс берді. Бірнеше қарапайым конструкциялар ұсынылды, соның ішінде Heinkel P.1077 Julia, онда ұшқыш майданды кішірейте түсу үшін жатып (қарнымен) ұшуға мүмкіндік берілді. "Джулия" бұл келісімшартқа ең лайықты деп есептелді. Алғашқы жоспар ұшақты тік көтеру болған, бірақ кейін бұл идея үш дөңгелекті арбадан көлденең ұшыруға өзгертілді, бұл Arado Ar 234 реактивтік барлаушы-бомбалаушысының алғашқы сегіз прототипінде қолданылған тәсілге ұқсас.
In 1943, Luftwaffe air superiority was being challenged by the Allies over the Reich and radical innovations were required to overcome the crisis. Surface to air missiles appeared to be a promising approach to counter the Allied strategic bombing offensive; a variety of projects were started, but invariably problems with the guidance and homing systems prevented any of these from attaining operational status. Providing the missile with a pilot, who could operate a weapon during the brief terminal approach phase, offered a solution. Submissions for a simple target defence interceptor were requested by the Luftwaffe in early 1944 under the umbrella of the Jägernotprogramm, literally "Emergency Fighter Program". A number of simple designs were proposed, including the Heinkel P.1077 Julia, in which the pilot lay prone (on his stomach), to reduce the frontal area. The Julia was the front runner for the contract. The initial plan was to launch the aircraft vertically, but this concept was later changed to a conventional horizontal take off from a tricycle wheeled trolley, similar to that used by the first eight prototypes of the Arado Ar 234 jet reconnaissance bomber.
Бахемнің ұсынысы
Наттерді алғаш рет 1944 жылдың тамызында доктор Эрих Бахем Германияның ірі қаласына американдық бомбалау шабуылының куәсі болғаннан кейін ойлап тапты. Ол осы бомбалаушылардың үлкен тобын таратудың бір жолы болуы керек деп сенді. Оның BP 20 ("Natter") - бұл Fieseler-де жұмыс істеген Fi 166 концепциясының дизайны, бірақ басқа ұсыныстарға қарағанда әлдеқайда радикалды болды. Ол жабыстырылған және шегеленген ағаш бөліктерінен, броньдалған бөлімінен және пилот кабинасының алдыңғы жағында оқ өткізбейтін шыныдан жасалған. Бастапқыда машинаны Walter HWK 109 509A 2 зымырандық қозғалтқышымен жабдықтау жоспарланған еді, алайда Me 163 ұшағында қолданылған 109 509A 1 ғана қолжетімді болды. Оның теңіз деңгейіндегі итеру күші "бос жүріс" күйінде толық қуатқа дейін өзгеріп отыратын. "Natter" ұшағының артқы жағында орнатылған Шмиддинг SG34 қатты отынмен жұмыс істейтін зымырандық күшейткіштері тік ұшыру кезінде қосымша итеру күшін қамтамасыз ету үшін пайдаланылды, олар 10 секунд бойы жұмыс істеп, содан кейін өшіп, тасталатын болды. Эксперименттік прототиптер үш жолмен жоғары сатылы болаттан жасалған ұшыру мұнарасына көтерілді, олардың бірі әр қанаттың ұшы үшін, екіншісі - құйрықтың төменгі ұшы үшін арналған. Ұшақ мұнарадан шыққан кезде, оның аэродинамикалық беттері тұрақты ұшуды қамтамасыз етуге жеткілікті жылдамдыққа жетеді деп үміттенілді. Операциялық жағдайда, "Natter" ұшыру қондырғысынан шыққаннан кейін, ол кейбір V 2 зымырандарын ұшыруларда қолданылатын сәулелік басқару мүмкіндігі бар автопилотпен одақтас бомбалаушыларға жақын бағытталатын болады. Тек содан кейін ғана ұшқыш басқаруды, нысананы алу және қару қолдану мүмкіндігіне ие болады, ол бастапқыда он тоғыз 55 мм R4M зымырасынан тұратын залп ретінде ұсынылды. Кейіннен 28 R4M немесе 73 мм Henschel Hs 297 Föhn зымырандары ұсынылды, олардың әрқайсысы "Natter" ұшағының мұрнына орнатылған ұялы ұшыру түтікшелерінен атылатын. "Natter" бомбалаушылардың үстінен және артынан ұшуға арналған, сол кезде оның Walter қозғалтқышының отыны бітіп қалуы мүмкін. Бір реттік шабуылдан кейін ұшқыш енді планерге айналған "Natter" ұшағын шамамен 100 метр биіктікке дейін түсіріп, ұшақтың мұрнын және артқы фюзеляждан кішкентай тежегіш парашютті босатып, тегістеп тастайтын. Фюзеляждың жылдамдығы төмендеп, ұшқыш өзінің инерциясымен алға лақтырылып, жеке парашютпен қонатын. 1944 жылдың тамызында жасалған алғашқы ұсыныста "Natter" конструкциясының бетон мұрны болды; машина бомбалаушыға соғылуы мүмкін екені айтылды, бірақ бұл ұсыныс кейіннен "Natter" жобасынан алынып тасталды. Бахем бастапқы ұсыныста "Natter" өзін-өзі өлтіру қаруы емес екенін және ұшқыш үшін қауіпсіздік мүмкіндіктерін жобалауға көп күш жұмсалғанын нақты айтты. Бұл жобаның бәсекелестерінен бір шешуші артықшылығы бар - ол әуе базасына қозғалтқышы жоқ желкенді машинаны қондыру қажеттілігін болдырмады, бұл, Me 163 зымыран ұшағының тарихы көрсеткендей, ұшақты одақтас ұшақтарының шабуылына өте осал етті.
The Natter was first conceived by Dr Erich Bachem in August 1944, after witnessing an American bombing raid on a major German city. He believed there ought to be a way to break up these large formations of bombers. His BP 20 ("Natter") was a development from a design he had worked on at Fieseler, the Fi 166 concept, but considerably more radical than the other submissions. It was built using glued and nailed wooden parts with an armour plated bulkhead and bulletproof glass windshield at the front of the cockpit. The initial plan was to power the machine with a Walter HWK 109 509A 2 rocket engine; however, only the 109 509A 1, as used in the Me 163, was available. It had a sea level thrust variable between at "idle" to at full power, with the Natter's intended quartet of rear flank mount Schmidding SG34 solid fuel rocket boosters used in its vertical launch to provide an additional thrust for 10 seconds before they burned out and were jettisoned. The experimental prototypes slid up a tall vertical steel launch tower for a maximum sliding length of in three guideways, one for each wing tip and one for the lower tip of the ventral tail fin. By the time the aircraft left the tower it was hoped that it would have achieved sufficient speed to allow its aerodynamic surfaces to provide stable flight. Under operational conditions, once the Natter had left the launcher, it would be guided to the proximity of the Allied bombers by an autopilot with the possibility of an added beam guidance similar to that used in some V 2 rocket launches. Only then would the pilot take control, aim and fire the armament, which was originally proposed to be a salvo of nineteen 55mm R4M rockets. Later, 28 R4Ms or a number of the larger, 73mm Henschel Hs 297 Föhn rockets were suggested, with either variety of unguided rocket fired from the Natter's nose mounted cellular launch tubes. The Natter was intended to fly up and over the bombers, by which time its Walter engine would probably be out of propellant. Following its one time attack with its rockets, the pilot would dive his Natter, now effectively a glider, to an altitude of around , flatten out, release the nose of the aircraft and a small braking parachute from the rear fuselage. The fuselage would decelerate and the pilot would be ejected forwards by his own inertia and land by means of a personal parachute. In an early proposal in August 1944, the Natter design had a concrete nose; it was suggested that the machine might ram a bomber, but this proposal was subsequently withdrawn in later Project Natter outlines. Bachem stated clearly in the initial proposal that the Natter was not a suicide weapon and much effort went into designing safety features for the pilot. The design had one decisive advantage over its competitors – it eliminated the necessity to land an unpowered gliding machine at an airbase, which, as the history of the Me 163 rocket aircraft had clearly demonstrated, made an aircraft extremely vulnerable to attack by Allied fighters.
Өзгерістер
Генрих Гиммлер Бахемнің жобасына қызығушылық танытты. Рейхсфюрер СС Бахемге сұхбат берді және жобаны толық қолдады. 1944 жылдың қыркүйек айының ортасында Вафен-СС техникалық басқармасы Бахемге Наттерді оның Валдзее зауытында әзірлеуге және өндіруге тапсырыс берді. Рейхслюфтфартминистериум (RLM/Германияның авиация министрлігі) BP 20 ұшағын Ba 349A деп ресми түрде белгіледі және құрылыс басталды. 1944 жылдың желтоқсанында жоба негізінен СС және Обергруппенфюрер Ханс Каммердің бақылауына көшті. Бұл шешім СС-тің ұшақтардың дизайнына және әуе шайқасы стратегиясына елеулі түрде араласуының жалғыз жағдайы болды. Жобаның басында RLM Наттердің инженерлік бағалауын жүргізді және оның нәтижелерін 1944 жылдың 28 қазанында жариялады. Наттерді біліктілігі жоқ жұмысшылармен, сапасыз құралдар мен арзан материалдарды пайдаланып құрастыруға арналған. Бұрыннан жұмсақ болған жобаға тағы да қатаң үнемдеу шаралары енгізілді. Наттерде қону шассисі болмады, бұл салмақты, шығындарды және құрылыс уақытын үнемдеді. Сондықтан, машинаның ең ерекше ерекшеліктерінің бірі - ұшқыштың қашып кетуі және машинаны құтқару болды. Бұл оқиғалардың жоспарланған реті мынадай болды: шабуылдан кейін Наттер төменгі биіктікке түсіп, көлденең ұшуға көше алатын. Содан кейін ұшқыш жақсы оқытылған қашып кету процедурасын орындайтын. Ол кабинаның қақпағын ашатын, ол ауа ағынында артқа қарай ашылатын. Келесі кезекте, ұшқыш қауіпсіздік белбеуін шешіп, аяқтарын руль педальдерінен шығаратын. Басқару бағанасына орнатылған тұтқаны басу арқылы ол бағананың түбіндегі құлыпты босатып, бағананы алға еңкеюге мүмкіндік беретін, содан кейін мұрынды босату механизміне арналған қауіпсіздік құлпын ашатын. Ол одан әрі алға еңкейіп, кабинаның алдындағы еденге жақын орналасқан тұтқаны тартып, мұрын бөлімін босататын, ол фюзеляждың алдыңғы бөлігіндегі аэродинамикалық қысымның төмендеуі салдарынан өзіндік түрде түсіп қалатын. Мұрын бөлігі ажырағанда, ол артқы фюзеляждың оң жағында сақталған кішкентай лента парашютті босататын екі кабельді қысқа уақытқа тартуға тиіс болды. Парашют ашылып, Наттерді тежейтін. Ұшқыш инерциясымен кабинадан шығарылып, фюзеляждан шыққаннан кейін жеке парашютын ашып, жерге түсетін. Артқы бөліктен құнды Вальтер ракеттік қозғалтқышын парашютпен түсіру жоспарланған, бұл ұшақты тежейтін және ұшқышты инерциямен шығаратын, алайда осы механизммен байланысты мәселелер жанжал аяқталғанға дейін толық шешілмеді. 1944 жылдың қыркүйегінде Берлин-Адельсхофтағы Аэродинамика институты Deutsche Versuchsanstalt für Luftfahrt (DVL) толық өлшемнің 40% -ына дейін үлкейтілген ағаш модельде жел тоннелінде сынақтар жүргізілді, жылдамдық 504 км/сағ дейін жетті. Осы сынақтардың нәтижелері 1945 жылдың қаңтарында Бахем Веркке жеткізілді. Völkenrode Braunschweig-тегі Luftfahrtforschungsanstalt Hermann Göring (LFA) базасында Мах 1-ге жуық жылдамдықпен қосымша модельдерді сынақтан өткізу жүргізілді. Наурыз айында Бахем Верк 1100 км/сағ жылдамдықпен қанағаттанарлық ұшу сапалары күтілуі керек деген хабарлама алды.
Heinrich Himmler became interested in Bachem's design. The Reichsführer SS granted Bachem an interview and fully supported the project. In the middle of September 1944, the Technical Office of the Waffen SS made an order for Bachem to develop and manufacture the Natter at his Waldsee factory. The Reichsluftfahrtministerium (RLM/German Aviation Ministry) officially designated the BP 20 the Ba 349A and construction began. During December 1944, the project came largely under the control of the SS and Obergruppenführer Hans Kammler. This decision is said to have been the only time the SS significantly interfered with aircraft design and air fighting strategy. Early on in the project, the RLM undertook an engineering assessment of the Natter, which it reported on 28 October 1944. The Natter was designed to be built by unskilled labor with poor quality tools and inexpensive material. Various stringent economies were imposed on an already frugal design. The Natter had no landing gear, which saved weight, expense and construction time. Consequently, one of the most unusual features of the machine was the escape of the pilot and recovery of the machine. The proposed sequence of these events was as follows: After the attack, the Natter might dive to a lower altitude and flatten out into level flight. The pilot would then proceed with a well practised escape sequence. He would open the cockpit canopy latch, which would allow the canopy to flick backwards on its hinge in the airstream. Next, the pilot would undo his seat belt and remove his feet from the rudder pedal stirrups. By squeezing a lever mounted on the control column, he would release a lock at the base of the column, which would allow him to tilt the column forwards where it could engage in and undo a safety latch for the nose release mechanism. He would then lean a little further forward and pull a lever hinged near the floor at the front of the cockpit, freeing the nose section, which self jettisoned as a result of the reduced aerodynamic pressure at the front of the fuselage. As the nose section separated, it was intended to briefly pull on two cables that released a small ribbon parachute stored on the starboard side of the rear fuselage. The parachute subsequently opened and decelerated the Natter. The pilot would be ejected from the cockpit by his own inertia and as soon as he was clear of the fuselage, he would open his personal parachute and descend to the ground. A parachute was to eject the valuable Walter rocket engine from the rear, which would decelerate the aircraft and eject the pilot with inertia, however, associated problems with this mechanism were still not fully resolved prior to the conflict's end. Wind tunnel testing on a wooden model, scaled to 40% of full size, was performed at the Deutsche Versuchsanstalt für Luftfahrt (DVL), the Institute for Aerodynamics at Berlin Adlershof in September 1944 at speeds up to 504 km/h. Results from these tests were reported in January 1945 to the Bachem Werk. Further model tests were carried out at the Luftfahrtforschungsanstalt Hermann Göring (LFA) facility in Völkenrode Braunschweig, at speeds close to Mach 1. In March the Bachem Werk simply received a statement that satisfactory flying qualities should be expected with speeds up to 1,100 km/h.
Ұшу сынақтары
Бірінші эксперименталды прототиптің құрылысы 1944 жылдың 4 қазанында аяқталды. V1 кейіннен Baumuster1 (BM1) деп аталды, ал кейін "B" әрпі алынып тасталды және машина M1 деп аталды. Келесі прототиптердің көпшілігі "М" кодтарымен белгіленді, сияқты Heinkel He 162 прототиптері де. Адамды тасымалдайтын жолсермеуші ұшулар 1944 жылдың 3 қарашасында басталды. Бірінші планер M1, 3000 метр биіктікке дейін Нюбург-ан-дер-Донауда Heinkel He 111 бомбалаушысымен кабель арқылы (Tragschlepp режимі) сүйретілді. Ұшқышы – Эрих Клокнер, ол төрт рет Tragschlepp ("сүйреп көтеру") ұшуын жүзеге асырды. M1 прототипінің сынақ бағдарламасын аяқтағаннан кейін ол парашютпен секіріп түсті және машина жерге құлады. Зерттеулер көрсетті, жолсермеу кабельі және М3 прототипінің жағдайында шасси, планерлердің ұшу қасиеттеріне кедергі келтірді, сондықтан нәтижелерді интерпретациялау қиын болды. Тік ұшып көтерілу сынақтары Вюртембергтегі Штеттен-ам-калтен-Маркт қаласының жанындағы Труппенюбунгсплатц (әскери оқу алаңы) Хеубергтегі Охсенкопф тауында жүргізілді. Бірінші сәтті пилотсыз тік ұшып көтерілу, эксперименталды ұшыру мұнарасынан 1944 жылдың 22 желтоқсанында орын алды. Сынақ машинасы M16, барлық ерте тік ұшыру сынақтарындағыдай, тек Шмиддинг қатты бустерлерімен жұмыс істеді. 1945 жылдың 1 наурызына дейін 16 прототип пайдаланылды, сегізі жолсермеуші ұшу сынақтарында, ал сегізі VTO (тік ұшып көтерілу) сынақтарында.
Construction of the first experimental prototype Natter, Versuchsmuster 1, was completed on 4 October 1944. V1 was subsequently referred to as Baumuster1 (BM1) and later still the "B" was dropped and the machine became known as the M1. Most subsequent prototypes were known by 'M' codes, as the later prototypes of the Heinkel He 162 were. Manned glider flights began on 3 November 1944. The first glider M1 was towed to around 3,000 m by a Heinkel He 111 bomber with a cable (Tragschlepp mode) at Neuburg an der Donau. The pilot was Erich Klöckner, who made all four documented Tragschlepp ("towed") flights. After carrying out the test programme of the M1, he bailed out and the machine crashed into the ground. It was found that the towing cable, and in the case of the M3, the undercarriage interfered with the flight characteristics of the gliders and consequently the results were difficult to interpret. The vertical take off trials were conducted on high ground called the Ochsenkopf at the Truppenübungsplatz (military training area) Heuberg near Stetten am kalten Markt, Württemberg. The first successful unmanned vertical take off from the experimental launch tower occurred on 22 December 1944. The test machine, the M16, was powered only by the Schmidding solid boosters, as were all the early vertical launch trials. Up to and including 1 March 1945, 16 prototypes had been used, eight in glider trials and eight in VTO trials.
Адамды ұшу сынағы
1945 жылдың қаңтарында Бахемге Берлин билігі ақпан айының соңына дейін пилоттық ұшу жүргізуді талап етті. 25 ақпанда M22 эксперименталды ұшыру мұнарасында болды. Ол Walter HWK 109 509 A1 қозғалтқышымен бірінші рет орнатылған, мүмкіндігінше толық жұмыс істейтін машина болды. Кокпитте манекен-ұшқыш болды. Мұнарадан ұшып шығу өте сәтті болды. Инженерлер мен жердегі экипаж M22 төрт Schmidding күштеуішін және Walter қозғалтқышының біріктірілген күшімен көтерілгенін, жалпы ұшқыш күшінің шамамен есептелгенін, мұрын бөлігінің бағдарлама бойынша ажыратылғанын және манекен-ұшқыштың жеке парашютымен қауіпсіз жерге түскенін бақылады. Фюзеляждың қалған бөлігі екі үлкен құтқару парашютымен түсті, бірақ жерге тиген кезде Walter сұйық отынды ракета қозғалтқышының қалдық гиперголдық отыны (Т-тотықтырғыш және С-отын) жарылып, машина жойылды. Бахемнің сынақ бағдарламасы қысқартылғанына қарамастан, 1 наурызда Люфтваффедің жас ерікті сынақ ұшқышы Лотар Сибер толық отынмен толтырылған M23 пилот кабинасына кірді. Ұшақ машинадағы түрлі бақылау сенсорларынан ұшу деректерін беру үшін FM-радио хабарламасымен жабдықталған. Сибер мен ұшыру алаңындағы инженерлер арасында пилоттық ұшуларда қолданылатын жүйеге ұқсас, сымды байланыс арқылы сөйлесу құрылғысы болды. Сағат 11:00-де M23 ұшуға дайын болды. Ochsenkopf тауының үстінде төменгі қабатты бұлттар жатыр. Walter сұйық отынды ракета қозғалтқышы толық қуатқа жетті және Сибер төрт қатты күштеуішті іске қосу үшін батырманы басты. Бастапқыда Natter тік көтерілді, бірақ шамамен биіктігі 15 метрде кенеттен 30 градусқа бұрылып, кері қисыққа түсті. Содан кейін ұшқыштар кабинасы ұшып кетті. Natter жоғары жылдамдықпен көтеріліп, көлденеңнен 15 градус бұрышпен бұлттарға сіңіп кетті. Walter қозғалтқышы ұшып шыққаннан кейін 15 секундтан кейін тоқтады. Natter шамамен биіктікке жеткендігі болжанып отыр, содан кейін 32 секундтан соң ұшыру алаңынан бірнеше шақырым жерге қатты құлап түсті. Ол кезде белгісіз болғандай, Schmidding күштеуіштерінің бірі ажыратылмады және оның қалдықтары 1998 жылы апат орнынан табылды. Ұшқыш апатқа дейін ұзақ бұрын есінен таныған болуы мүмкін. Бахем Сибердің 3G үдеу күшінің әсерінен басқару тұтқасын рефлекстік түрде кері тартып алғанын болжады. Ұшыру алаңының жанында құлаған шатырды тексеру көрсетті, құлыптың ұшы бүгілген, бұл ұшыру кезінде толық жабылмаған болуы мүмкін екенін көрсетеді. Ұшқыштың бас тірегі шатырдың астыңғы жағына бекітілген, ал шатыр ұшып кеткен кезде ұшқыштың басы кенеттен қатты ағаштан жасалған артқы кабинаның қабырғасына соқтығып, Сиберді есінен танытып немесе мойнын сындырып жіберген болуы мүмкін. Апат Бахемнің ұзақ уақыттан бері сақтап келген сенімін нығайтты: ұшып шығу және нысанаға жақын жердегі ұшу толығымен автоматтандырылуы керек. Шатыр құлпы күшейтілді және бас тірегі кабинаның артқы тақтасына бекітілді. Сынақ бағдарламасында автопилот енгізілгенге дейін басқару тұтқасында уақытша құлыптау құрылғысы болады, ол машинаға кем дегенде тік көтерілуге және содан кейін пилот оны босатуға мүмкіндік береді. Walter қозғалтқышының жұмысын тоқтату себебі Natterдің дерлік төңкерілгендігі және отын бактерілерінің сорғы құбырларына ауа кіргендігі болуы мүмкін, нәтижесінде қозғалтқыш отын жетіспеуден тоқтады. Сибер таза ракеталық қуатпен жерден тік ұшып шыққан алғашқы адам болды, бұл Юрий Гагариннің "Восток-1" орбиталық ұшуына 16 жыл бұрын болды. Сибердің қазасынан кейін Natter ұшуларының барлығы сегіз ұшу да пилотсыз жүргізілді.
By January 1945, Bachem was under pressure from the authorities in Berlin to carry out a manned flight by the end of February. On 25 February, M22 was in the experimental launch tower. It was as complete an operational machine as possible with the Walter HWK 109 509 A1 engine installed for the first time. A dummy pilot was in the cockpit. Lift off from the tower was perfect. The engineers and ground crew watched as the M22 ascended under the combined power of the four Schmidding boosters and the Walter engine, an estimated total thrust of The nose separated as programmed and the dummy pilot descended safely under its personal parachute. The remainder of the fuselage came down under its two large salvage parachutes, but when it hit the ground the Walter liquid propellant rocket engine's residual hypergolic propellants (T Stoff oxidizer and C Stoff fuel) exploded and the machine was destroyed. Despite Bachem's concerns that the test programme had been significantly cut short, a young volunteer Luftwaffe test pilot, Lothar Sieber, climbed into the cockpit of the fully fuelled M23 on 1 March. The aircraft was equipped with an FM transmitter for the purpose of transmitting flight data from various monitoring sensors in the machine. A hard wire intercom appears to have been provided between Sieber and the engineers in the launch bunker using a system similar to that used in the manned glider flights. Around 1100 am, the M23 was ready for take off. Low stratus clouds lay over the Ochsenkopf. The Walter liquid fueled rocket engine built up to full thrust and Sieber pushed the button to ignite the four solid boosters. Initially, the Natter rose vertically but, at an altitude of about , it suddenly pitched up into an inverted curve at about 30° to the vertical. At about the cockpit canopy was seen to fly off. The Natter continued to climb at high speed at an angle of 15° from the horizontal and disappeared into the clouds. The Walter engine stalled about 15 seconds after take off. It is estimated the Natter reached , at which point it nose dived and hit the ground with great force about 32 seconds later, some kilometres from the launch site. Unknown at the time, one of the Schmidding boosters failed to jettison and its remains were dug up at the crash site in 1998. The pilot was likely unconscious long before the crash. Bachem surmised Sieber had involuntarily pulled back on the control column under the effect of the 3 G acceleration. Examination of the canopy, which fell near the launch site, showed the tip of the latch was bent, suggesting it may not have been in the fully closed position at launch. The pilot's headrest had been attached to the underside of the canopy and as the canopy flew off the pilot's head would have snapped back suddenly about , hitting the solid wooden rear upper cockpit bulkhead, and either knocking Sieber unconscious or breaking his neck. The accident reinforced Bachem's long held belief that the take off and flight in the vicinity of the target bombers should be fully automated. The canopy latch was strengthened and the headrest was attached to the backboard of the cockpit. Before the introduction of the autopilot in the test programme, the control column would have a temporary locking device on it, which would allow the machine to ascend vertically to at least and then be removed by the pilot. The Walter engine probably ceased operation because the Natter was virtually upside down and air may have entered the intake pipes in the propellant tanks, starving the engine. Sieber had become the first person to take off vertically from the ground under pure rocket power, 16 years before Yuri Gagarin's Vostok 1 pioneering, peacetime orbital flight. Following Sieber's death, all of the eight subsequent Natter flights were unmanned.
Өндіріс
СС 150 «Наттер» тапсырыс берді, ал Люфтваффе 50 «Наттер» тапсырыс берді, бірақ соғыс аяқталғанға дейін ешқайсысы жеткізілмеді. Бахем заводында құрастырылған «Наттерлердің» саны және олардың тағдыры туралы көптеген пікірлер айтылды. Бахемнің мәлімдемесіне сәйкес, соғыс аяқталғанға дейін Вальдзедегі Бахем заводында 36 «Наттер» шығарылды. Бұл жаңа ұшыру платформасы да Хьюбергте салынды, ол эксперименттік болат мұнарадан көп алыс емес жерде орналасқан. Сәуір айында екі тік полюстен ұшырылғаны туралы құжаттар бар, бірақ Бахемнің соғыстан кейінгі баяндамасында айтылған үш емес. Санкт-Леонард-им-Пицтальда қолға түскен төрт «Наттердің» екеуі АҚШ-қа жіберілді. Екінші дүниежүзілік соғыста Германияда салынған бір ғана түпнұсқа «Наттер» Смитсониан институтының басқаруымен Мэриленд штатының Суитленд қаласындағы Пол Э. Гарбердің сақтау, қалпына келтіру және қоймалау орталығында сақтаулы тұр. АҚШ-қа әкелінген басқа «Наттерлердің» тағдыры белгісіз. «Наттердің» Мюрок полигонынан ұшырылғаны туралы ешқандай құжаттық дерек жоқ. Санкт-Леонард-им-Пицтальдағы «Наттерлердің» бірінің құйрық бөлігі әлі тіркемеде тұрғанда сындырылып қалды.
The SS ordered 150 Natters, and the Luftwaffe ordered 50, but none were delivered by the end of the war. Much debate has surrounded the number of Natters built at the Bachem Werk and their disposition. According to Bachem, 36 Natters were produced at the Bachem Werk in Waldsee by the end of the war. This new launcher was also constructed on the Heuberg, not far from the experimental steel tower. There is documentary evidence for two pole launches in April but not three as claimed by Bachem in his post war presentation. Of the four Natters captured at Sankt Leonhard im Pitztal, two went to the United States. Only one original Natter built in Germany in the Second World War survives in storage at the Paul E. Garber Preservation, Restoration, and Storage Facility in Suitland, Maryland, under the auspices of the Smithsonian Institution. The fate of the other Natter brought to the US is unknown. There is no documentary evidence that a Natter was ever flown from Muroc Field. The tail section of one of the Natters at Sankt Leonhard im Pitztal was broken off while it still rested on its trailer.
Тұрақтылық
1945 жылдың ақпан айының басында А1 операциялық машинасының ұшу профилі кезінде ауырлық орталығының орналасуы RLM және SS-ті алаңдатты. Олар бұл көрсеткіштерді алдағы А1 ұшағының құрылысына қатысты белгілеуді қалады, ол Krokus Einsatz (Operation Crocus) – Natter-дің далалық қолданылуы үшін арналған болатын. Ауырлық орталығының орналасуы негізгі қанаттың хордасының (жетек және артқы жиектері арасындағы қашықтық) пайызы ретінде беріледі. Осылайша, 0% – жетек жиегі, ал 100% – артқы жиегі. Адам басқаратын жолсермеуші сынақтарында ауырлық орталығы 20 мен 34% аралығында өзгерді. 8 ақпанда өткен инженерлер кеңесінде A1 Krokus машинасы үшін күтілетін ауырлық орталығының өзгерістері талқыланды. Төрт қатты күштеуіштің салмағымен ұшу кезінде ауырлық орталығы 65%-қа дейін жылжуы тиіс еді, бірақ осы ракеталарды босатудан кейін ол 22%-ға дейін алға жылжыды. 14 ақпанда Зюберттің еркін ұшуы кішкентай Natter-дің жолсермеуші ретінде тамаша ұшу қасиеттеріне ие екенін нақты көрсетті. Ауырлық орталығы мәселесі бастапқыда бір метрлік қосымша құйрық қанаттарын орнату арқылы шешілді, олар күштеуіштерді босатумен бірге шығарылды. Француз әскерлері келгенге дейін Bachem Werk қызметкерлерінің тобы бес A1 Natter-ді тіркемеде Австрияға аттанды. Бад-Вершофенде топ Наберн-унтер-Текке бір Natter-мен қайтып келген басқа отрядты күтті. Содан кейін екі топ Австрия Альпіне қарай жолға шықты. Екі Natter-мен бір топ Инн өзені мен оның саласы Эцталер-Ахе өзендерінің қосылған жеріндегі Шлатт лагеріне жетті. Екінші топ төрт ұшақпен Санкт-Леонард-им-Пицтальға барды. АҚШ әскерлері бірінші топты 4 мамыр күні Шлатт лагерінде, ал екінші топты келесі күні ұстады. Жоба барысында Bachem Werk-ке BP 20 Natter-дің толық мәліметтерін жапондықтарға беруге бұйрық берілді, бірақ олардың оны алған-алмағанына күмән болды. Дегенмен, олардың Natter туралы жалпы білімі бар екені және жобаға үлкен қызығушылық танытқаны белгілі болды. Үш бетонды іргетастың ортасында шамамен 50 сантиметр тереңдікте шаршы ойық бар, ол бір кезде ұшыру мұнарасының негізі ретінде қызмет еткен. Әр ойықтың жанында жер бетінен кесілген құбыр орналасқан, ол бұрын кабельдік желіге арналған болуы мүмкін. Бұл үш бетонды алаңды 1945 жылдың күзінде жер өлшеуші байқаған, бірақ 1999 жылға дейін қайтадан табылған жоқ. 27 қаңтарда сегіз ұшқыш алғашқы операциялық ұшуларға ерікті болып тіркелді және 5 ақпанда Bachem зауытында Natter-мен танысуға кірісті. Бұл оқу сәуір айының басына дейін жалғасты. Ұшқыштар 20 сәуірде, Гитлердің туған күнінде үш жауынгерлік дайын Natter ұшағымен ұшуды күткен, бірақ ұшыру алаңдарының әлі толыққанды дайын еместігін білмеді. Бірақ сол күні АҚШ-тың 10-шы бронетанкті дивизиясы өз танктерін Хасенхольц орманның солтүстік-батысына қарай Кирххайм-унтер-Текке қарай айдап әкелді. Келесі күні олар автобанды кесіп өтіп, тікелей Natter операциялық аймағына бет алды. Natter тобы кейіннен Валдзеге шегінді.
In early February 1945, the positions of the centre of gravity for the A1 operational machine during its flight profile were giving the RLM and the SS cause for concern. They wanted these figures to be decided upon for the upcoming construction of the A1 aircraft for Krokus Einsatz (Operation Crocus), the field deployment of the Natter. The position of the centre of gravity is expressed as a percentage of the chord (distance between the leading and trailing edges) of the main wing. Thus 0% is the leading edge and 100% is the trailing edge. In the manned glider trials the centre of gravity had been varied between 20 and 34%. At a meeting of engineers held on 8 February, the variations in the centre of gravity expected in the A1 Krokus machine were discussed. At take off with the weight of the four solid boosters, the centre of gravity would be brought back to 65%, but after releasing these rockets it would move forwards to 22%. The free flight by Zübert on 14 February had showed unequivocally that the little Natter had excellent flying characteristics as a glider. The centre of gravity problem was solved initially by the addition of one metre square auxiliary tailfins that were released simultaneously with the jettisoning of the boosters. Shortly before the French troops arrived, a group of Bachem Werk personnel set out for Austria with five A1 Natters on trailers. At Bad Wörishofen, the group waited for another squad retreating from Nabern unter Teck with one completed Natter. Both groups then set out for the Austrian Alps. One group with two Natters ended up at the junction of the river Inn and one of its tributaries, the Ötztaler Ache, at Camp Schlatt. The other group went to St. Leonhard im Pitztal with four aircraft. US troops captured the first group at Camp Schlatt around 4 May and the second group on the following day. At some time during the project, the Bachem Werk was ordered to give complete details of the BP 20 Natter to the Japanese, but there was doubt over whether they had received them. They were, however, known to have a general knowledge of the Natter and showed considerable interest in the project. In the centre of each of the three concrete footings is a square hole approximately 50 centimeters deep, which once served as the foundation for the launch tower. Beside each hole is a pipe, cut off at ground level, which was probably once a cable pit. These three concrete pads were noticed by a surveyor in the autumn of 1945, but not rediscovered until 1999. On 27 January, eight pilots volunteered for the first operational flights and started familiarizing themselves with the Natter at Bachem's factory on 5 February. This training continued until the beginning of April. The pilots were expecting to fly three combat ready Natters on 20 April, which was Hitler's birthday, but were unaware that the launch pads were still incomplete. But on that day the US 10th Armored Division drove its tanks into Kirchheim unter Teck to the northwest of Hasenholz wood. The next day it crossed the autobahn and headed straight for the Natter operational area. The Natter group subsequently retreated to Waldsee.
Тірі қалған ұшақтар мен олардың көшірмелері
Тек бір түпнұсқа A1 Natter сақталған; ол АҚШ-тың Мэриленд штатындағы Сутлендтегі Пол Э. Гарбердің сақтау, қалпына келтіру және қоймалау орталығында сақталған. Ол нашар күйде және жалпы жұртшылыққа қолжетімді емес. Дәлелдер бұл машинаның 1945 жылдың мамыр айында Австрияның Санкт-Леонард-им-Питцталь қаласында АҚШ әскерлерімен тұтқынға алынғанын көрсетеді. Бұл машина болат мұнарадан ұшырылатын экспериментальді типке жатады және M17 сияқты боялған. Әлемде Наттердің бірнеше статикалық көшірмелері бар, мысалы, Калифорния штаты Чино қаласындағы Planes of Fame әуе мұражайында және Флорида штаты Полк-Сити қаласындағы Fantasy of Flight мұражайында, АҚШ-та.
Only one original A1 Natter survives; it is stored in the Paul E. Garber Preservation, Restoration and Storage Facility in Suitland, Maryland, US. It is in a poor state of repair and is no longer accessible to the general public. The evidence supports the proposition that this machine was captured by US troops at St. Leonhard im Pitztal, Austria in May 1945. This machine is of the experimental type as launched from the steel tower and is painted to look like an M17. There are several static reproductions of Natters around the world, for example at the Planes of Fame Air Museum, Chino, California and Fantasy of Flight, Polk City, Florida, US.
Фильм
2010 жылы Оливер Гортат пен Филип Шнайдер Бахем Ба 349 туралы деректі фильм жасады.
In 2010, Oliver Gortat and Philip Schneider made a documentary film about the Bachem Ba 349.