STS-61B: 1985 ж. «Атлантис» ғарыш кемесінің 23-ші NASA миссиясы. 3 спутникті ұшырды, орбитада құрылыс тәсілдерін сынады. Жылдам қайта іске қосылу рекорды!
Ағылшыншамен салыстырыңыз: абзацты басыңыз — түпнұсқа терезеде ашылады. Абзац астындағы EN түймесі оны мәтін ішінде көрсетеді.
Мазмұны
Кіріспе
1985 жылы америкалық экипажбен ғарышқа ұшу. STS-61B – NASA ғарыш бағдарламасының 23-ші миссиясы және «Space Shuttle Atlantis» ғарыш кемесін пайдаланған екінші миссия. 1985 жылдың 26 қарашасында Флорида штатындағы Кеннеди ғарыш орталығынан ұшырылды. STS-61B миссиясы барысында экипаж үш коммуникациялық спутникті орбитаға шығарды және орбитада құрылыстар салу тәсілдерін сынады. «Атлантис» 1985 жылдың 3 желтоқсанында, орбитада 6 күн, 21 сағат, 4 минут және 49 секунд болғаннан кейін Калифорния штатындағы Эдвардс әуе базасына қонды. STS-61B – тарихында ғарыш кемесінің ең жылдам қайта ұшырылуы болды – «Атлантис» STS-51J миссиясынан кейін STS-61B миссиясына дейін арада бар болғаны 54 күн өтті. 2022 жылға дейін бұл бір ғарыш кемесінің екі ұшырылымы арасындағы рекорд болып табылады. Миссия сонымен қатар алғашқы мексикалық астронавт Родольфо Нери Веланың қатысуымен ерекшеленді. Бұл «Атлантис» үшін 1986 жылғы «Челленджер» трагедиясынан бұрынғы екінші және соңғы миссия болды. «Челленджер» трагедиясы ғарыш кемесінің барлық флотын екі жарым жылға тоқтатты, ал «Атлантис» үш жылдан кейін, 1988 жылдың 2 желтоқсанында ұшырылған STS-27 миссиясына дейін қайта ұшпады.
1985 American crewed spaceflight
STS 61 B was the 23rd NASA Space Shuttle mission, and its second using Space Shuttle Atlantis. The shuttle was launched from Kennedy Space Center, Florida, on November 26, 1985. During STS 61 B, the shuttle crew deployed three communications satellites, and tested techniques of constructing structures in orbit. Atlantis landed at Edwards Air Force Base, California, at 16:33:49 EST on December 3, 1985, after 6 days, 21 hours, 4 minutes, and 49 seconds in orbit. STS 61 B marked the quickest turnaround of a Shuttle orbiter from launch to launch in history – just 54 days elapsed between Atlantis launch on STS 51 J and launch on STS 61 B. as of 2022, this is still the record for turn around between two flights of the same orbital space vehicle. The mission was also notable for carrying the first Mexican astronaut, Rodolfo Neri Vela. This was also Atlantis second and final mission before the Space Shuttle Challenger disaster in 1986. The Challenger disaster would ground the shuttle fleet for two and a half years and Atlantis would not fly again until STS 27, which launched three years later on December 2, 1988.
Экипаждың отыру орындары
Орынды таңдау, ұшыру, қону. 1–4 орын Ұшу палубасында. 5–7 орын Ортаңғы палубада. S1 Шоу Шоу S2 О'Коннор О'Коннор S3 Росс Спринг S4 Клив Клив S5 Спринг Росс S6 Уокер Уокер S7 Нери Вела Нери Вела
Seat Launch Landing Seats 1–4 are on the Flight Deck. Seats 5–7 are on the Middeck. S1 Shaw Shaw S2 O'Connor O'Connor S3 Ross Spring S4 Cleave Cleave S5 Spring Ross S6 Walker Walker S7 Neri Vela Neri Vela
Шаттл өңдеуі
1985 жылы 7 қазанда STS-51J миссиясын аяқтағаннан кейін Эдвардс әуе күштері базасына қонған «Атлантис» 1985 жылы 12 қазанда Кеннеди ғарыш орталығына қайта оралды. Шаттл бірден Орбиталық өңдеу кешеніне (OPF) жеткізілді, онда ұшудан кейінгі техникалық қызмет көрсету және келесі ұшуға дайындық бірдей уақытта жүргізілді. Ғарыш шаттлы бағдарламасы тарихындағы ең жылдам өңдеу рекорды бойынша, OPF-те бар болғаны 26 күн өткен соң, 1985 жылы 7 қарашада шаттл Көлік құрастыру ғимаратына (VAB) ауыстырылды. «Атлантис» сыртқы жанармай багы (ET) және қатты отынды күшейткіштер (SRB) жиынтығымен біріктіріліп, 1985 жылы 12 қарашада LC 39A ұшыру алақанына шығарылды.
After landing at the Edwards Air Force Base at the end of STS 51 J on October 7, 1985, Atlantis returned to the Kennedy Space Center on October 12, 1985. The shuttle was moved directly into an Orbiter Processing Facility (OPF), where post flight de servicing and pre flight processing took place simultaneously. After only 26 days in the OPF, a record fast processing in the history of the Space Shuttle program, the shuttle was rolled to the Vehicle Assembly Building (VAB) on November 7, 1985. Atlantis was mated with the External Tank (ET) and Solid Rocket Booster (SRB) stack and was rolled out to launch LC 39A on November 12, 1985.
Пайдалы жүктеме
Бұл миссияда үш спутник орбитаға шығарылды: Aussat 2, Morelos 2 және Satcom K2. Aussat 2 және Morelos 2 өздерінің сериясындағы екінші спутниктер болды (сериядағы алғашқы спутниктер STS 51 I және STS 51 G миссияларында орбитаға шығарылған). Бұл екі спутник те Hughes Space and Communications HS 376 спутниктері болып, геостационарлық транзиттік орбитаға (GTO) жету үшін Пайдалы жүктемеге көмектесетін модуль (PAM D) күшейткішімен жабдықталды. Satcom K2 – RCA American Communications (RCA) компаниясына тиесілі және осы компания басқаратын RCA 4000 сериялы спутниктердің бір түрі болды. Бұл спутник PAM D2 күшейткіші арқылы орбитаға шығарылды (ол PAM D-нің үлкендеу нұсқасы). Бұл PAM D2 күшейткішінің ғарыш шаттлымен жасалған алғашқы ұшырылысы еді. Үш спутник те бірінен соң бірі сәтті орбитаға шығарылды, олардың күшейткіш сатылары автоматты түрде іске қосылып, оларды геостационарлық транзиттік орбиталарға көтерді. Олардың иелері оларды қабылдап алды, содан кейін апогейдегі борттық жылдамдатқыштарды іске қосып, орбиталарды дөңгелектеді және экватормен сәйкестендірді.
Three satellites were deployed during this mission: Aussat 2, Morelos 2, and Satcom K2. Aussat 2 and Morelos 2 were the second satellites in their series (the first satellites in the series were deployed during STS 51 I and STS 51 G). Both of these were Hughes Space and Communications HS 376 satellites and were equipped with a Payload Assist Module (PAM D) booster to reach geostationary transfer orbit (GTO). Satcom K2 was a version of the RCA 4000 series satellites, which were owned and operated by RCA American Communications (RCA). This satellite was deployed using a PAM D2 booster (which was a larger version of the PAM D). This was the first flight of the PAM D2 booster on a Space Shuttle. All three satellites were successfully deployed, one at a time, and their booster stages fired automatically to lift them to geostationary transfer orbits. Their respective owners assumed charge, and later fired the onboard kick motors at apogee, to circularize the orbits and align them with the equator.
Басқа да нысандар
STS 61 B миссиясы кезінде Атлантис ғарыш кемесінде шахматты жарыс туы болды; қазір сол ту Индианаполис Мотор Спидвейінің Даңқ залы мұражайында қойылған. Бұл сонымен қатар Orbiter Experiments (OEX) жетілдірілген автопилотының екінші сынақ ұшуы болды. Ол шамамен 65 сағат бойы жұмыс істеді және орбиталық аппаратты тек алдыңғы соплолармен, тек артқы соплолармен ұшуға, басқа спутникке автоматты түрде жақындауға және аэродинамикалық қарсылық жоқ орбитада ұшуға қабілетті екенін көрсетті. OEX автопилоты базалық жүйеге қарағанда отынды үнемдірек пайдаланды.
A checkered racing flag was carried on board Atlantis during STS 61 B; the flag is now on display at the Indianapolis Motor Speedway Hall of Fame Museum. This was also the second test flight of the Orbiter Experiments (OEX) advanced autopilot. It ran for approximately 65 hours and demonstrated the ability to fly the orbiter on nose jets only, aft jets only, to automatically stationkeep on another satellite and to fly an orbit with zero aerodynamic drag. The OEX autopilot was also more fuel efficient than the baseline system.
Миссияның қысқаша мазмұны
"Атлантис" ғарыш кемесі Кеннеди ғарыш орталығының 39А ұшыру алаңынан 1985 жылғы 26 қарашада сағат 19:29:00 EST уақытында ұшырылды. Бұл ұшыру ғарыш бағдарламасының екінші түнгі ұшырылуы және 1985 жылғы тоғызыншы және соңғы ұшу болды. Миссияның маңызды мақсаты – ғарышта ірі құрылымдарды құрастыруға арналған EASE/ACCESS эксперименті. EASE/ACCESS – Лэнгли зерттеу орталығы (LRC) мен Маршалл ғарыш ұшу орталығының (MSFC) бірлескен жобасы. ACCESS – көптеген кішкентай тіреулер мен түйіндерден тұратын "биік" мұнара. EASE – бірнеше ірі арқалықтар мен түйіндерден құралған, кері пішінді пирамида тәрізді геометриялық құрылым. Бұл эксперименттер ғарышта алдын ала дайындалған ірі құрылымдарды құрастыру мүмкіндігін көрсетті. Астронавттар Росс пен Спринг миссия барысында екі рет ғарышқа шықты, бұл АҚШ үшін 50-ші және 51-ші, ал ғарыш кемесі бағдарламасы үшін 12-ші және 13-ші ғарышқа шығу сапары болды. Жүк бөліміне орнатылған IMAX камерасы EASE/ACCESS жұмысына қатысқан астронавттардың қызметін және басқа да қызықты көріністерді түсірді. "Бұл, әдетте, ғарыш станциясын салудың қалаулы жолы емес", - деді Росс кейін EASE туралы. Астронавттар ғарышқа шығудың ең қиын бөлігінің EASE арқалықтарын ұстап тұрып, өз дене салмағын басқару екенін хабарлады. Олар ACCESS жақсы жұмыс істейтінін, ал EASE еркін қозғалуды тым көп талап ететінін анықтады. Астронавттар бес-алты күн бойы күн сайын алты сағаттан ғарышқа шығудың мүмкін екенін айтты және қолғаптарды ауыстыру арқылы қолдың шаршауын азайтуды ұсынды. Росс EVA брифингінде экипаж екінші ғарыш сапарында Manned Maneuvering Unit (MMU) пайдалануға тырысқанын айтты, себебі "кейбір жағдайларда ол өте пайдалы болар еді. Атап айтқанда, егер сіз орбиталық станцияға бекітілген ғарыш станциясының бөліктерін құрастырсаңыз, онда оларды манипулятор қол жеткізе алмайтын жерге жылжытуға болар еді". Ол MMU-ны шатттың роботтық манипуляторының (Canadarm) жетпейтін жерлеріне кабельдер мен құралдарды орнату үшін де пайдалануға болатынын қосты. Миссия барысында астронавт Родольфо Нери Вела негізінен адам физиологиясына қатысты бірқатар эксперименттер жүргізді. Сондай-ақ, ол Жерді бақылау миссиясының аясында Мексика мен Мехико қаласының суретін түсірді. Алайда, командир Брюстер Шоу люктің құлпына кілт іліп қойды, өйткені ол мексикалықтың миссия кезінде "жағдайынан айырылуы" мүмкін деп алаңдады. Шоу Нэри Веланың кілтке назар аудармағанын, бірақ экипаждың басқа мүшелері байқағанын айтты.
Space Shuttle Atlantis lifted off from Launch Complex 39A at Kennedy Space Center at 19:29:00 p. m. EST on November 26, 1985. The launch marked the second night launch of the Space Shuttle program, and the ninth and final flight of 1985. A key element of the mission's objectives was EASE/ACCESS, an experiment in assembling large structures in space. EASE/ACCESS was a joint venture between the Langley Research Center (LRC) and the Marshall Space Flight Center (MSFC). ACCESS was a "high rise" tower composed of many small struts and nodes. EASE was a geometric structure shaped like an inverted pyramid, that was composed of a few large beams and nodes. Together, these experiments demonstrated the feasibility of assembling large preformed structures in space. Astronauts Ross and Spring performed two spacewalks on the mission, which marked the 50th, and 51st extravehicular activity (EVAs) for the United States, and the 12th and the 13th for the Shuttle program. An IMAX camera mounted in the cargo bay filmed the activities of the astronauts engaged in the EASE/ACCESS work, as well as other scenes of interest. "This is probably not the preferred way of building a space station", Ross said later of EASE. The astronauts reported that the most difficult part of the spacewalks was torquing their own masses while holding the EASE beams. They found that ACCESS worked well, while EASE required too much free floating. The astronauts judged that performing six hour spacewalks every other day over a five or six day period was feasible, and recommended glove changes to reduce hand fatigue. Ross said in the EVA debrief that the crew had tried to have the Manned Maneuvering Unit (MMU) manifested for use in the second spacewalk, because "for certain applications it would be very useful. In particular if you were building portions of a space station attached to the orbiter, then moving those portions farther than the manipulator arm could transport them". He added that the MMU could be used to attach cable runs and instruments in places that were out of reach of the shuttle's robotic arm (Canadarm). During the mission astronaut Rodolfo Neri Vela accomplished a series of experiments, that were primarily related to human physiology. He also photographed Mexico and Mexico City as part of the mission's Earth observations. However, Commander Brewster Shaw installed a padlock on the hatch control because he was "particularly concerned" that the Mexican could "flip out" during the mission. Shaw had noted that he didn't think that Neri Vela noticed the padlock, but that the other members of the crew did.
Ғарышқа шығу
STS 61 B миссиясы барысында екі ғарыштан шығу операциясы (EVA) жүргізілді, олар ғарыш станциясын құрастыруда қолданылуы мүмкін құрастыру техникаларын көрсету мақсатында болды.
Two spacewalks were conducted during the STS 61 B mission to demonstrate assembly techniques which might be used in space station assembly. EVA Spacewalkers Start (UTC) End Duration EVA 1 Jerry L. RossSherwood C. Spring November 29, 1985 November 29, 1985 5 hours 32 minutes EVA 1 focused on human performance during assembling of an experimental erectable truss structure. Ross and Spring first assembled the Assembly Concept for Construction of Erectable Space Structures (ACCESS) assembly jig in Atlantis payload bay. Each cell was assembled in the jig, then pushed up so that the next cell could be assembled. The astronauts assembled the ACCESS truss in 55 minutes, (EVA time line allotted two hours for a single ACCESS assembly) so they assembled it and built it again. The Experimental Assembly of Structures through EVA (EASE) task involved putting together beams weighing to make a three sided pyramid assessed the capabilities of free floating astronauts. EASE was scheduled to be assembled six times, but Ross and Spring managed eight assemblies. During the first four assemblies the astronauts used foot restraints. In his post flight debriefing, Spring noted that his fingers grew numb during the third EASE assembly and very tired during the fourth. At the end of the EVA Spring assembled and hand deployed a small target satellite to be used after the EVA as a station keeping target for Atlantis, which played the role of an automated orbital maneuvering vehicle in rendezvous software tests. EVA 2 Jerry L. RossSherwood C. Spring December 1, 1985 December 1, 1985 6 hours 41 minutes The purpose of EVA 2 was to assess the ability of astronauts to handle large structural elements and the ability of the Shuttle's robotic arm (Canadarm), to support future station assembly. Ross and Spring assembled nine bays of ACCESS, then placed parts for the tenth bay on the Canadarm. Ross stepped into the Manipulator Foot Restraint (MFR) and astronaut Mary C. Cleave positioned him within reach of the top of the ACCESS girder, where he assembled the tenth bay. The parts were not tethered. Ross performed a cable run assembly simulation by attaching a tether along the side of the tower while Cleave positioned him. Then Spring released the bottom of the tower so Ross could try to precisely handle the beam from the RMS. He replaced it in the assembly jig where it started, demonstrating astronaut ability to assemble a truss in one place and install it in another. Spring then replaced Ross on the MFR. He changed a beam on the tower to simulate structural repair, then pointed the truss at the Moon to judge his handling ability. The astronauts took down ACCESS, and Spring assembled EASE from the RMS. Before finishing, he joined two beams to simulate handling a thermal control heat pipe. Ross unlatched the EASE pyramid so that Spring could maneuver it. Then he replaced Spring on the MFR to duplicate the EASE activities.
EVA ғарышкерлерінің басталуы (UTC) Аяқталуы Ұзақтығы
EVA 1 Джерри Л. Росс Шервуд С. Спринг 29 қараша, 1985 29 қараша, 1985 5 сағат 32 минут
Two spacewalks were conducted during the STS 61 B mission to demonstrate assembly techniques which might be used in space station assembly. EVA Spacewalkers Start (UTC) End Duration EVA 1 Jerry L. RossSherwood C. Spring November 29, 1985 November 29, 1985 5 hours 32 minutes EVA 1 focused on human performance during assembling of an experimental erectable truss structure. Ross and Spring first assembled the Assembly Concept for Construction of Erectable Space Structures (ACCESS) assembly jig in Atlantis payload bay. Each cell was assembled in the jig, then pushed up so that the next cell could be assembled. The astronauts assembled the ACCESS truss in 55 minutes, (EVA time line allotted two hours for a single ACCESS assembly) so they assembled it and built it again. The Experimental Assembly of Structures through EVA (EASE) task involved putting together beams weighing to make a three sided pyramid assessed the capabilities of free floating astronauts. EASE was scheduled to be assembled six times, but Ross and Spring managed eight assemblies. During the first four assemblies the astronauts used foot restraints. In his post flight debriefing, Spring noted that his fingers grew numb during the third EASE assembly and very tired during the fourth. At the end of the EVA Spring assembled and hand deployed a small target satellite to be used after the EVA as a station keeping target for Atlantis, which played the role of an automated orbital maneuvering vehicle in rendezvous software tests. EVA 2 Jerry L. RossSherwood C. Spring December 1, 1985 December 1, 1985 6 hours 41 minutes The purpose of EVA 2 was to assess the ability of astronauts to handle large structural elements and the ability of the Shuttle's robotic arm (Canadarm), to support future station assembly. Ross and Spring assembled nine bays of ACCESS, then placed parts for the tenth bay on the Canadarm. Ross stepped into the Manipulator Foot Restraint (MFR) and astronaut Mary C. Cleave positioned him within reach of the top of the ACCESS girder, where he assembled the tenth bay. The parts were not tethered. Ross performed a cable run assembly simulation by attaching a tether along the side of the tower while Cleave positioned him. Then Spring released the bottom of the tower so Ross could try to precisely handle the beam from the RMS. He replaced it in the assembly jig where it started, demonstrating astronaut ability to assemble a truss in one place and install it in another. Spring then replaced Ross on the MFR. He changed a beam on the tower to simulate structural repair, then pointed the truss at the Moon to judge his handling ability. The astronauts took down ACCESS, and Spring assembled EASE from the RMS. Before finishing, he joined two beams to simulate handling a thermal control heat pipe. Ross unlatched the EASE pyramid so that Spring could maneuver it. Then he replaced Spring on the MFR to duplicate the EASE activities.
EVA 1 эксперименталды тіреулі конструкцияны құрастыру барысында адамның өнеміне қатысты зерттеулерге бағытталды. Росс пен Спринг алдымен «Атлантис» ғарыш кемесінің жүк бөлімінде Эректемелі ғарыш құрылымдарын құрастыру тұжырымдамасының (ACCESS) құрастыру тірегін құрастырды. Әрбір бөлімше тіректе жиналып, содан кейін келесі бөлімшені құрастыру үшін жоғары итерілді. Астронавттар ACCESS конструкциясын 55 минутта құрастырды (бір ACCESS құрастыруға EVA уақыт кестесінде екі сағат көзделген), сондықтан олар оны жинап, қайтадан құрастырды.
Two spacewalks were conducted during the STS 61 B mission to demonstrate assembly techniques which might be used in space station assembly. EVA Spacewalkers Start (UTC) End Duration EVA 1 Jerry L. RossSherwood C. Spring November 29, 1985 November 29, 1985 5 hours 32 minutes EVA 1 focused on human performance during assembling of an experimental erectable truss structure. Ross and Spring first assembled the Assembly Concept for Construction of Erectable Space Structures (ACCESS) assembly jig in Atlantis payload bay. Each cell was assembled in the jig, then pushed up so that the next cell could be assembled. The astronauts assembled the ACCESS truss in 55 minutes, (EVA time line allotted two hours for a single ACCESS assembly) so they assembled it and built it again. The Experimental Assembly of Structures through EVA (EASE) task involved putting together beams weighing to make a three sided pyramid assessed the capabilities of free floating astronauts. EASE was scheduled to be assembled six times, but Ross and Spring managed eight assemblies. During the first four assemblies the astronauts used foot restraints. In his post flight debriefing, Spring noted that his fingers grew numb during the third EASE assembly and very tired during the fourth. At the end of the EVA Spring assembled and hand deployed a small target satellite to be used after the EVA as a station keeping target for Atlantis, which played the role of an automated orbital maneuvering vehicle in rendezvous software tests. EVA 2 Jerry L. RossSherwood C. Spring December 1, 1985 December 1, 1985 6 hours 41 minutes The purpose of EVA 2 was to assess the ability of astronauts to handle large structural elements and the ability of the Shuttle's robotic arm (Canadarm), to support future station assembly. Ross and Spring assembled nine bays of ACCESS, then placed parts for the tenth bay on the Canadarm. Ross stepped into the Manipulator Foot Restraint (MFR) and astronaut Mary C. Cleave positioned him within reach of the top of the ACCESS girder, where he assembled the tenth bay. The parts were not tethered. Ross performed a cable run assembly simulation by attaching a tether along the side of the tower while Cleave positioned him. Then Spring released the bottom of the tower so Ross could try to precisely handle the beam from the RMS. He replaced it in the assembly jig where it started, demonstrating astronaut ability to assemble a truss in one place and install it in another. Spring then replaced Ross on the MFR. He changed a beam on the tower to simulate structural repair, then pointed the truss at the Moon to judge his handling ability. The astronauts took down ACCESS, and Spring assembled EASE from the RMS. Before finishing, he joined two beams to simulate handling a thermal control heat pipe. Ross unlatched the EASE pyramid so that Spring could maneuver it. Then he replaced Spring on the MFR to duplicate the EASE activities.
Эксперименттік ғарыштан шығу арқылы құрылымдарды құрастыру (EASE) міндеті үш жақты пирамида жасау үшін салмақты арқалықтарды біріктіруді қамтыды, бұл еркін қозғалатын астронавттардың қабілеттерін бағауға мүмкіндік берді. EASE алты рет құрастырылуы жоспарланған, бірақ Росс пен Спринг сегіз рет құрастырды. Алғашқы төрт құрастыру кезінде астронавттар аяқ тіректерін пайдаланды. Ұшудан кейінгі брифингісінде Спринг үшінші EASE құрастыру кезінде саусақтарының ұюын және төртіншісінде шаршағанын атап өтті. EVA соңында Спринг кішкентай мақсатты спутникті жинап, қолмен орналастырды, ол EVA аяқталғаннан кейін «Атлантис» станциясын ұстау үшін нысана ретінде пайдаланылды, ол кездесу бағдарламалық қамтамасыз ету сынақтарында автоматтандырылған орбиталық маневрлік көлік құралының рөлін атқарды.
Two spacewalks were conducted during the STS 61 B mission to demonstrate assembly techniques which might be used in space station assembly. EVA Spacewalkers Start (UTC) End Duration EVA 1 Jerry L. RossSherwood C. Spring November 29, 1985 November 29, 1985 5 hours 32 minutes EVA 1 focused on human performance during assembling of an experimental erectable truss structure. Ross and Spring first assembled the Assembly Concept for Construction of Erectable Space Structures (ACCESS) assembly jig in Atlantis payload bay. Each cell was assembled in the jig, then pushed up so that the next cell could be assembled. The astronauts assembled the ACCESS truss in 55 minutes, (EVA time line allotted two hours for a single ACCESS assembly) so they assembled it and built it again. The Experimental Assembly of Structures through EVA (EASE) task involved putting together beams weighing to make a three sided pyramid assessed the capabilities of free floating astronauts. EASE was scheduled to be assembled six times, but Ross and Spring managed eight assemblies. During the first four assemblies the astronauts used foot restraints. In his post flight debriefing, Spring noted that his fingers grew numb during the third EASE assembly and very tired during the fourth. At the end of the EVA Spring assembled and hand deployed a small target satellite to be used after the EVA as a station keeping target for Atlantis, which played the role of an automated orbital maneuvering vehicle in rendezvous software tests. EVA 2 Jerry L. RossSherwood C. Spring December 1, 1985 December 1, 1985 6 hours 41 minutes The purpose of EVA 2 was to assess the ability of astronauts to handle large structural elements and the ability of the Shuttle's robotic arm (Canadarm), to support future station assembly. Ross and Spring assembled nine bays of ACCESS, then placed parts for the tenth bay on the Canadarm. Ross stepped into the Manipulator Foot Restraint (MFR) and astronaut Mary C. Cleave positioned him within reach of the top of the ACCESS girder, where he assembled the tenth bay. The parts were not tethered. Ross performed a cable run assembly simulation by attaching a tether along the side of the tower while Cleave positioned him. Then Spring released the bottom of the tower so Ross could try to precisely handle the beam from the RMS. He replaced it in the assembly jig where it started, demonstrating astronaut ability to assemble a truss in one place and install it in another. Spring then replaced Ross on the MFR. He changed a beam on the tower to simulate structural repair, then pointed the truss at the Moon to judge his handling ability. The astronauts took down ACCESS, and Spring assembled EASE from the RMS. Before finishing, he joined two beams to simulate handling a thermal control heat pipe. Ross unlatched the EASE pyramid so that Spring could maneuver it. Then he replaced Spring on the MFR to duplicate the EASE activities.
EVA 2 Джерри Л. Росс Шервуд С. Спринг 1 желтоқсан, 1985 1 желтоқсан, 1985 6 сағат 41 минут
Two spacewalks were conducted during the STS 61 B mission to demonstrate assembly techniques which might be used in space station assembly. EVA Spacewalkers Start (UTC) End Duration EVA 1 Jerry L. RossSherwood C. Spring November 29, 1985 November 29, 1985 5 hours 32 minutes EVA 1 focused on human performance during assembling of an experimental erectable truss structure. Ross and Spring first assembled the Assembly Concept for Construction of Erectable Space Structures (ACCESS) assembly jig in Atlantis payload bay. Each cell was assembled in the jig, then pushed up so that the next cell could be assembled. The astronauts assembled the ACCESS truss in 55 minutes, (EVA time line allotted two hours for a single ACCESS assembly) so they assembled it and built it again. The Experimental Assembly of Structures through EVA (EASE) task involved putting together beams weighing to make a three sided pyramid assessed the capabilities of free floating astronauts. EASE was scheduled to be assembled six times, but Ross and Spring managed eight assemblies. During the first four assemblies the astronauts used foot restraints. In his post flight debriefing, Spring noted that his fingers grew numb during the third EASE assembly and very tired during the fourth. At the end of the EVA Spring assembled and hand deployed a small target satellite to be used after the EVA as a station keeping target for Atlantis, which played the role of an automated orbital maneuvering vehicle in rendezvous software tests. EVA 2 Jerry L. RossSherwood C. Spring December 1, 1985 December 1, 1985 6 hours 41 minutes The purpose of EVA 2 was to assess the ability of astronauts to handle large structural elements and the ability of the Shuttle's robotic arm (Canadarm), to support future station assembly. Ross and Spring assembled nine bays of ACCESS, then placed parts for the tenth bay on the Canadarm. Ross stepped into the Manipulator Foot Restraint (MFR) and astronaut Mary C. Cleave positioned him within reach of the top of the ACCESS girder, where he assembled the tenth bay. The parts were not tethered. Ross performed a cable run assembly simulation by attaching a tether along the side of the tower while Cleave positioned him. Then Spring released the bottom of the tower so Ross could try to precisely handle the beam from the RMS. He replaced it in the assembly jig where it started, demonstrating astronaut ability to assemble a truss in one place and install it in another. Spring then replaced Ross on the MFR. He changed a beam on the tower to simulate structural repair, then pointed the truss at the Moon to judge his handling ability. The astronauts took down ACCESS, and Spring assembled EASE from the RMS. Before finishing, he joined two beams to simulate handling a thermal control heat pipe. Ross unlatched the EASE pyramid so that Spring could maneuver it. Then he replaced Spring on the MFR to duplicate the EASE activities.
EVA 2-нің мақсаты астронавттардың үлкен құрылымдық элементтерді басқару қабілетін және ғарыш кемесінің роботтық манипуляторының (Canadarm) болашақ станцияны құрастыруды қолдау қабілетін бағалау болды. Росс пен Спринг ACCESS-тің тоғыз бөлімін құрастырды, содан кейін оныншы бөліктің элементтерін Canadarm-ке орналастырды. Росс Манипуляторлық аяқ тірегіне (MFR) кірді, ал астронавт Мэри К. Кливе оны ACCESS арқауының жоғарғы жағына жеткізді, онда ол оныншы бөлімін құрастырды. Бөлшектер байланыспаған. Росс кабельді орнату симуляциясын мұнараның жанындағы арқанды бекіту арқылы орындады, ал Кливе оны орналастырды. Содан кейін Спринг мұнараның төменгі бөлігін босатты, сонда Росс RMS сәулесін дәл басқаруға тырысты. Ол оны бастапқы құрастыру тірегіне қайтарды, бұл астронавттың бір жерде конструкцияны құрастырып, басқа жерге орнату қабілетін көрсетті. Спринг Росты MFR-де ауыстырды. Ол мұнарадағы бір сәулені ауыстырып, құрылымдық жөндеуді симуляциялады, содан кейін конструкцияны Айға бағыттап, оның басқару қабілетін бағалады. Астронавттар ACCESS-ті түсірді, ал Спринг RMS-тен EASE-ті құрастырды. Аяқтамас бұрын, ол жылуды басқару жылу құбырын симуляциялау үшін екі сәулені біріктірді. Росс EASE пирамидасын босатып, Спрингке оны маневрлеуге мүмкіндік берді. Содан кейін ол EASE қызметін қайталау үшін MFR-де Спрингтің орнын алды.
Two spacewalks were conducted during the STS 61 B mission to demonstrate assembly techniques which might be used in space station assembly. EVA Spacewalkers Start (UTC) End Duration EVA 1 Jerry L. RossSherwood C. Spring November 29, 1985 November 29, 1985 5 hours 32 minutes EVA 1 focused on human performance during assembling of an experimental erectable truss structure. Ross and Spring first assembled the Assembly Concept for Construction of Erectable Space Structures (ACCESS) assembly jig in Atlantis payload bay. Each cell was assembled in the jig, then pushed up so that the next cell could be assembled. The astronauts assembled the ACCESS truss in 55 minutes, (EVA time line allotted two hours for a single ACCESS assembly) so they assembled it and built it again. The Experimental Assembly of Structures through EVA (EASE) task involved putting together beams weighing to make a three sided pyramid assessed the capabilities of free floating astronauts. EASE was scheduled to be assembled six times, but Ross and Spring managed eight assemblies. During the first four assemblies the astronauts used foot restraints. In his post flight debriefing, Spring noted that his fingers grew numb during the third EASE assembly and very tired during the fourth. At the end of the EVA Spring assembled and hand deployed a small target satellite to be used after the EVA as a station keeping target for Atlantis, which played the role of an automated orbital maneuvering vehicle in rendezvous software tests. EVA 2 Jerry L. RossSherwood C. Spring December 1, 1985 December 1, 1985 6 hours 41 minutes The purpose of EVA 2 was to assess the ability of astronauts to handle large structural elements and the ability of the Shuttle's robotic arm (Canadarm), to support future station assembly. Ross and Spring assembled nine bays of ACCESS, then placed parts for the tenth bay on the Canadarm. Ross stepped into the Manipulator Foot Restraint (MFR) and astronaut Mary C. Cleave positioned him within reach of the top of the ACCESS girder, where he assembled the tenth bay. The parts were not tethered. Ross performed a cable run assembly simulation by attaching a tether along the side of the tower while Cleave positioned him. Then Spring released the bottom of the tower so Ross could try to precisely handle the beam from the RMS. He replaced it in the assembly jig where it started, demonstrating astronaut ability to assemble a truss in one place and install it in another. Spring then replaced Ross on the MFR. He changed a beam on the tower to simulate structural repair, then pointed the truss at the Moon to judge his handling ability. The astronauts took down ACCESS, and Spring assembled EASE from the RMS. Before finishing, he joined two beams to simulate handling a thermal control heat pipe. Ross unlatched the EASE pyramid so that Spring could maneuver it. Then he replaced Spring on the MFR to duplicate the EASE activities.
Ояту қоңырауы
NASA "Жетіздер" жобасы кезінде астронавттарға музыка ойнау дәстүрін бастады және алғаш рет "Аполлон-15" миссиясында ұшқыштар экипажын ояту үшін музыка қолданды. Әрбір таңдау арнайы жасалады, көбінесе астронавттардың отбасылары таңдайды, және әдетте экипаж мүшесінің бірі үшін ерекше мағынаға ие болады немесе олардың күнделікті жұмысына қатысты келеді. Ұшу күні Әнші/Композитор Ойналған күні 2-ші күні "Әуе күштері әнұраны" Брюстер Х. Шоу-младший 3-ші күні "Американың сұлулығы" 4-ші күні "Теңіз жаяу әскері әнұраны" Брайан О'Коннор 5-ші күні "Нотр-Дам жеңіс маршы" Джерри Л. Росс 6-шы күні "АҚШ-та туған" Брюс Спрингстин.
NASA began a tradition of playing music to astronauts during the Project Gemini, and first used music to wake up a flight crew during Apollo 15. Each track is specially chosen, often by the astronauts' families, and usually has a special meaning to an individual member of the crew, or is applicable to their daily activities. Flight Day Song Artist/Composer Played for Day 2 "Air Force Hymn" Brewster H. Shaw Jr. Day 3 "America the Beautiful" Day 4 "Marine Corps Hymn" Bryan O'Connor Day 5 "Notre Dame Victory March" Jerry L. Ross Day 6 "Born in the U. S. A." Bruce Springsteen