Бірінші дүниежүзілік соғыстағы француз танкысы Schneider CA 1

French tank developed during WWI

The Schneider CA 1 (originally named the Schneider CA) was the first French tank, developed during the First World War. The Schneider was inspired by the need to overcome the stalemate of trench warfare which on the Western Front prevailed during most of the Great War. It was designed specifically to open passages for the infantry through barbed wire and then to suppress German machine gun nests. After a first concept by Jacques Quellennec devised in November 1914, the type was developed from May 1915 onwards by engineer Eugène Brillié, paralleling British development of tanks the same year. Colonel Jean Baptiste Eugène Estienne in December 1915 began to urge for the formation of French armoured units, leading to an order in February 1916 for four hundred Schneider CA tanks, which were manufactured by SOMUA, a subsidiary of Schneider located in a suburb of Paris, between September 1916 and August 1918. Like most early tanks, the Schneider was built like a simple armoured box, without compartmentalisation of the inner space. It lacked a turret, with the main armament, a short 75 mm cannon, in a sponson on the right side. By later standards it would therefore have been an assault gun instead of a tank. The vehicle was considered a very imperfect design, because of a poor layout, insufficient fire power, a cramped interior and inferior mobility due to an overhanging nose section, which had been designed to crush through the belts of barbed wire but in practice caused the tank to get stuck. Improved designs were almost immediately initiated but the production of these, the Schneider CA 2, CA 3 and CA 4, was eventually cancelled. The Schneider CA 1 tanks were widely used in combat during the last war years. Their first action on 16 April 1917 was largely a failure, the tank units suffering heavy losses, but later engagements were more successful. In 1918 the Schneider tanks played an important role in halting the German spring offensive and breaking the German front in the French summer offensives. They were active until the end of September 1918, less than two months before the Armistice of 11 November 1918, their numbers having dropped considerably due to attrition. After the war the surviving tanks were mostly rebuilt as utility vehicles but six Schneider tanks were deployed by Spain in the Rif War in Morocco and the type saw its last action in the beginning of the Spanish Civil War.

Before the First World War, mechanic Charles Marius Fouché cooperated with engineer Édouard Quellennec and the latter's son Jacques Quellennec to adapt existing caterpillar tractors to the conditions of Egyptian and French farming, among them the Holt Model 75. In this context in 1914 contacts were made with engineer Eugène Brillié of Schneider & Co. to adapt the Castéran Flexible Track Tractor. When that year war broke out, Jacques Quellennec was drafted as an infantry sergeant, witnessed most men of his unit being slaughtered during the First Battle of the Marne and was then severely wounded at the end of October. While recovering, he devised plans for an armoured tractor armed with a machine gun and capable of destroying German machine gun nests. Many in this period had comparable ideas but contrary to most, Quellennec had excellent contacts. Fouché had become a second lieutenant with the Grand Parc Automobile de Réserve of the Service Automobile, the Army branch responsible for motorisation, and Brillié was chief designer with one of France's main arms manufacturers. Early December, Quellennec met Fouché in Paris and both then went to Brillié to present drawings of a tracked armoured fighting vehicle. During a second visit Quellennec urged Brillié to bring over two Holt Model 75 tractors, at that time present in Tunisia, to France in order to perform the first trials. Brillié showed himself less than enthusiastic about the idea, objecting there would be not enough room on a tractor for both crew and armament. In February 1915, Quellennec was sent to an air force training base and tasked Fouché with trying to convince Brillié, without much apparent success. Meanwhile, the Schneider company had been given the order to develop heavy artillery tractors in January 1915. On 30 January it sent out its chief designer, Brillié, to investigate tracked tractors from the American Holt Company, at that time participating in a test programme at Aldershot in England. On his return, Brillié, who had earlier been involved in designing armoured cars for Spain, apparently without mentioning being influenced in this by Quellennec, Among the onlookers were General Philippe Pétain, and Colonel Jean Baptiste Eugène Estienne — an artillery man and engineer held in very high regard throughout the army for his unmatched technological and tactical expertise. The results of the prototype tank were, at least according to Estienne, For Estienne the vehicle shown embodied concepts about armoured fighting vehicles which he had been advocating since August 1914. Already on 1 December Estienne had proposed to the French GHQ the use of tracked armoured tractors to move infantry, equipment and cannon over the battlefield, having performed some trials with British caterpillar tractors. On 11 December Estienne let a certain lieutenant Thibier draw a sketch of two conceptions: the one of a Baby Holt chassis fitted at the front and the back with auxiliary rollers, to improve the trench crossing capacity; the other of an elongated suspension protected by side armour. From this it was concluded that the tank was sufficiently developed to justify a production order. On 25 February 1916 the War Ministry secretly ordered the production of four hundred tracteurs chenilles type Schneider & Cie blindés ("tracked and armoured tractors of the Schneider type"), at a price of 56,000 French francs per vehicle. For security reasons it was pretended these were simple towing vehicles, tracteurs Estienne. Fouché was ordered to improve the prototype, which resulted in a slightly changed L'appareil n° 1 Type B, tested on 2 March. Further changes, now including improvised side armour extending to the front in a bow, created the L'appareil n° 1 Type C or Machine Profilée which was tested on 17 March. On 27 February, Schneider had been asked to provide a first armoured superstructure made of boiler steel, which was late March placed on the eight wheeled chassis. and a prototype porteur variant of it, intended to carry a heavy artillery piece, the CD3. This would seem to indicate that the CA suffix was merely a Schneider product code similar to those used by Renault. At the end of 1916, the type was called Schneider CA 1 to make a distinction with a derived tank project, the Schneider CA 2. In 1917 the Schneider CA 1 is also called the Schneider 1916 to distinguish it from the Schneider 1917, another name for the next tank project, the Schneider CA 3. This had its origin in a demand by Estienne on 30 January 1917 to agree on a standardised terminology. General Mourret then proposed to use the official designations Schneider Modèle 1916 and Saint Chamond Modèle 1916.

The Schneider is effectively an armoured steel box on top of a caterpillar tractor. It has no turret; the main armament is a 75 mm Blockhaus Schneider "fortification gun" in a barbette in the right front corner of the tank. The right side had been chosen because the gunner had to stand to the left of the barrel to operate the gun. The cannon type was developed from a 75 mm trench mortar that had been adapted to fire from a fixed fortification position by adding a recoil compensator and a gun shield; in this configuration it weighed This short barrelled cannon had a length of just 9.5 calibres. It fired the standard French HE Model 1915 75 mm shell but with a reduced propelling charge, shortening the overall length of the round from to , allowing for a muzzle velocity of only The maximum range of the gun was metres, the practical range was and the tank needed to close within of a target for precision shooting. In its mounting the gun had a traverse of 60°, a depression of 10° and an elevation of 30°. The tank carried ninety rounds for the gun stowed vertically in bins to the right of the cannon (20), extreme right rear corner (14), left of the engine (32) and left rear corner (24). Secondary armement was two 8 mm Hotchkiss M1914 machine guns in the sides of the tank in large hemispherical ballmounts, and resting on pintles. Its High Command now envisaged a far larger number of tanks, demanding the import or manufacture of about 1,500 Schneiders. After it had become clear that the French industry did not have the spare capacity to meet those demands and that they far out reached the possibilities of domestic production, it was decided to produce the smaller, cheaper and more modern FIAT 3000 (a copy of the Renault FT) instead, three of which had been received in May 1918.

During production, the type was gradually improved, which caused further delays. From the 245th vehicle onwards an automatic starter was installed, engaged by a handle, as the original manual system did not allow for a sufficiently quick response to a changing battlefield situation. Also it was decided the design was too poorly protected. In response to the first use of British Mark I tanks on 15 September 1916, the Germans had begun to introduce anti tank weapons and tactics. One of the measures taken by them was the issuing of the Kerngeschoss or "K bullet", a hardened steel core round capable of piercing the thin armour of tanks. To defeat it, from the 210th vehicle onwards the Schneider tank was fitted with extra 5.4 mm thick armour plates on the sides and front with a space of four centimetres between the main armour and these appliqué plates. Even without the spaced armour, the front plates would have been immune against K bullet fire from a distance of two hundred metres, because they were angled at 60°, providing an effective line of sight thickness of During the spring of 1917 existing vehicles were uparmoured (creating a surblindé version) by the army workshop at Champlieu. Some of these, such as a vehicle with series number 61213, were fitted with additional armour plates on the vertical front surfaces, including an extra rectangular shield around the gun barrel. On 1 April 1917 of the 208 tanks available only about a hundred had been retrofitted. None of the older tanks had at this point yet received the new starter engine, this part of the improvement process would take until the end of the summer. Much more far reaching were early proposals to fundamentally change the design, to be implemented during the production run. These were inspired by the awkward layout; in order to limit the width of the tank, the main armament had been placed in an inconvenient position. On 1 December 1916 a certain Lieutenant Saar submitted drawings showing a vehicle on which the 75 mm cannon had been replaced by a 47 mm gun turret, the number of machine guns was raised to six, the number of vision slits to eleven and the engine was located in the middle of the hull. On 28 and 29 December 1916 the Schneider company considered moving the 75 mm gun to the nose of the vehicle and give it a 120° traverse.

To deploy tanks, it was first needed to train crews and create tank units. On 14 July 1916 Estienne started to set up a training base at the Fort du Trou d'Enfer, a fortress at Marly le Roi, west of Paris. For reasons of secrecy this location was officially attached to the 81st Heavy Artillery Regiment, a depot unit. On 15 August the camp was formally established and quickly filled with recruits, most of them young volunteers from various French armies. At Marly the crews received their first instruction consisting of the basics of maintenance and a lot of driver training with an emphasis on crossing trenches, avoiding shell craters and running down trees and walls. Because no actual Schneider vehicles were available at first, Holt tractors were used instead; later boiler plate training chassis were employed with the superstructure removed and replaced by a protective wooden frame. From the spring of 1917 onwards about seven vehicles were used for this goal. For unit training and live fire exercises, which required much larger manoeuvre grounds, on 30 August 1916 a camp was established at Cercottes. It received its first training vehicles on 17 November 1916. To get better acquainted with the mechanical side of the tanks, most crew members left Cercottes for a month to work as a trainee at the SOMUA factory. New vehicles would normally be first delivered at Cercottes. In 1917 the Cercottes base grew to a strength of about five thousand men, many of them sent there from units trying to get rid of undesirable elements, forcing the base command to reduce manpower by again removing them. On 28 September 1916 a large instruction centre was established at Champlieu, south of Compiègne. This location, close to the frontline and officially part of the warzone, could serve for final training and sending out battle ready units to those armies needing them. The tank workshops were also located there, repairing and updating existing vehicles. Eventually, the tank units were to support the attack by the Fifth Army at the Aisne and were concentrated in a nine kilometres wide sector south of Juvincourt et Damary, chosen for its firm ground. The Germans had created a strong defensive belt in this area, held by four divisions of the Bavarian Army, with a depth of nine kilometres and divided into four main trench systems. The plan was for the French infantry to take the first and second trench within about four hours, advancing behind the "creeping barrage", after which the tanks would immediately exploit this success and maintain the momentum of the offensive by quickly progressing towards the third trench, directly followed by the infantry; together they would conquer the third and fourth trenches. The "strategic rupture" resulting from this and many adjoining attacks was to be exploited through deep penetrations by large reserve infantry armies, outflanking the Hindenburg Line from the south. Three Groupements were committed to the offensive. Two of these, named after their commanders Louis Bossut and Louis Léonard Chaubès, were attached to the 32nd and 5th Army Corps respectively and would engage on the first day. Groupement Bossut consisted of five groupes: AS 2, 4, 5, 6 and 9, thus fielding eighty tanks, as the AS in this phase of the war operated at full strength with four batteries of four tanks. Groupement Chaubès, created on 8 March, included AS 3, 7 and 8, with about forty eight tanks. Each Groupement was reinforced by a supply and recovery unit or Section de Réparations et de Ravitaillement which besides two unarmed Saint Chamonds and some Baby Holt tractors was equipped with two unarmed Schneider CA tanks, towing Troy trailers with fuel, bringing the total at 132 Schneider vehicles, at that date the largest tank force ever deployed. On 13 April the tank units concentrated behind the frontline. There they were joined by supporting infantry companies: five from the 154e R. I. of the 165e D. I. for Groupement Bossut and three of the 76e R. I. of the 125e D. I. for Groupement Chaubès. During the early morning of 16 April 1917 the Nivelle Offensive was launched. In the sector where the tanks operated the initial waves of French infantry succeeded in taking the first and second German trenches as planned, but with very heavy losses. The French artillery was insufficient in number to simultaneously sustain the creeping barrage and suppress the numerous German artillery batteries. This was aggravated by the German air superiority which allowed artillery observation planes to precisely direct German interdiction fire on the advancing French columns. Groupement Chaubès suffered many losses before it was even able to leave the French lines. When arriving at the frontline in the early afternoon, it had to assist the infantry in clearing the second trench of the last German remnants. These did not panic at the sight of the French tanks but had been trained to hide from them, leaving their cover to engage the French infantry when the armoured vehicles had moved on. At the end of the day, the French infantry proved unable to continue the offensive and the last surviving French tanks had to be withdrawn. More to the east, north of Berry au Bac after which village later the entire tank action would be named, Groupement Bossut proved more successful. It managed to cross the various trench lines losing only a few vehicles and in the late morning concentrated to carry on the offensive. However, around 11:00 the tank of Bossut, Trompe la Mort ("Dare devil") leading the advance, carrying a tricolour fanion blessed in the Sacré Cœur at Montmartre, received a direct heavy artillery hit, incinerating most of the crew and blowing Bossut himself from the rear entrance from which he had been directing the battle, killed by a shell splinter through the heart. Nevertheless, the Schneiders continued their progress, advancing several miles in a narrow penetration through a shallow valley towards the third German trench. The weakened infantry though, was unable to follow, forcing the tanks to wait for the arrival of reserve units. For several hours the tanks moved up and down the conquered terrain to avoid presenting static targets for the German artillery. Despite this many vehicles were hit, as they were in plain sight of German batteries on the surrounding hills. Flank assaults by Bavarian stormtroopers were repulsed. In the early evening, fresh infantry units together with the tanks conquered a sector of the third trench, marking the high tide of the French progress during the entire Second Battle of the Aisne. The Schneiders then withdrew, again suffering losses by artillery fire. The Nivelle Offensive was a grave disappointment, demoralising the French troops and leading to the French Army Mutinies. The sense of failure extended to the Schneider tanks. Their losses had indeed been heavy: 76 of the 128 combat tanks engaged had been lost. Many of these had burnt: 57 in total, 31 with Groupement Bossut and 26 with Groupement Chaubès. Most had been set on fire by German artillery: twenty three vehicles of Groupement Chaubès had been hit by indirect fire and fifteen of Groupement Bossut; this latter unit had fourteen tanks hit by direct fire. Investigations showed that most vehicles had carried additional fire hazards: to compensate the limited range two fifty litre cans of petrol had been attached to the rear and some crews had even stowed a third one inside; sometimes explosive charges had been stowed outside; each tank had a bottle of ether to mix with the petrol to boost the engine and to enhance the fighting spirit three litres of strong liquor had been provided at the start of the battle. Also the personnel losses had been high: 180 of the 720 crew members, and 40% of the supporting infantry had become casualties. On a positive note, twenty broken down tanks had been salvaged from the battlefield, all enemy infantry assaults had failed, and the spaced armour proved to be very resistant, beyond expectations, against small arms fire and shell splinters. The main technical complaint was that visibility from within the vehicle was poor for the driver as well as the gunners. Tactical lessons drawn were that tanks should spread out more to avoid artillery fire and had to cooperate more closely with the infantry. Groupement III, commanded by Captain Henri Lefebvre, was intended to assist an attack by the Fourth Army on 17 April at Moronvilliers. It consisted of two Schneider groups, AS 1 and AS 10, reinforced by some Saint Chamond tanks. When the initial infantry attacks largely failed, the tank attack was cancelled, also in view of the events the previous day.

Despite the general failure of the Nivelle Offensive and the ensuing mutinies, French High Command in May 1917 tried to make use of the force concentration at the Aisne by at least conquering the notorious Chemin des Dames positions. Part of the plan was a limited but strategically important objective: the German saillant east of Laffaux where the Hindenburg Line hinged on the Chemin des Dames, named after the hillock of the Moulin de Laffaux. This attack was to be supported by Groupement Lefebvre. To improve the cooperation with the infantry, the Groupement was reinforced by an infantry battalion specially trained in combined arms tactics, the 17e Bataillon de Chasseurs à Pied. Coordination with the artillery was improved by attaching a special observation plane, protected by six SPAD VII fighters, that had to identify German antitank batteries and have them destroyed by counterbattery fire; it also had to report the position of the tanks to higher command levels. The more general offensive was launched on 5 May. Whereas most infantry attacks along the Chemin des Dames were bloody failures that day, the tank attack on the Moulin de Laffaux largely attained its objectives. The Schneiders, advancing not in column but "line abreast", exploited the initial infantry conquest of the first trench by crossing the second and then assisted the foot soldiers in heavy and fluid battles with counterattacking German reserves. Eventually most tanks broke down and had to be left behind by the advancing infantry. Salvaging them proved difficult as thunderstorms made the surface of the in itself firm chalkstone of the area very slippery and the terrain was rough, dotted with ruins and intersected by ravines and quarries. The majority of the vehicles were repaired during the night, but the soil had so deteriorated that only a single battery of four was deployed on the sixth. Nevertheless, the Schneiders had made a good account of themselves. Of thirty three tanks engaged only five had been destroyed, three of them Schneiders. Casualties among the crews numbered fifty five, three of them fatal.

In the wake of the mutinies Philippe Pétain was appointed supreme commander. He tried to restore confidence by abstaining from overambitious offensive plans. Only in 1918 when the influx of American troops and new armoured vehicles would tip the balance in favour of the Entente, could decisive attacks be considered. His motto was therefore: J'attends les Américains et les chars ("I wait for the Americans and the tanks"). However, remaining purely inactive would undermine the morale; to bolster it a series of meticulously prepared small scale offensives were undertaken in which success was guaranteed by deploying an overwhelming numerical superiority, especially in artillery, to conquer a limited objective. On 23 October 1917 Pétain in one blow took the notorious Chemin des Dames crest, including the fortress of La Malmaison. The attack was supported by Groupement Chaubès, at the time consisting of AS 8, 11 and 12. Due to the losses in April, each AS now deployed twelve tanks. Including the supply vehicles the Schneider total numbered forty one. The command vehicles of AS 11 and AS 12 were that day the first French tanks ever to use radio equipment in battle. It had the standard suspension of the Schneider CA but its hull was significantly shortened so that the overhanging nose had disappeared. The 75 mm cannon had been replaced by a cylindrical turret, intended to be armed with a 47 mm gun and a machine gun, close to the rear of the hull. The hull was further diminished in size and weight by a considerable narrowing, and closing of the roofed skylight slit, which lowered its height. As a result, the type weighed only eight tonnes. During the testing the vehicle, though no longer getting itself stuck on an overhanging nose, still proved unable to climb out of muddy shell craters. It was concluded that the suspension should be lengthened by the equivalence of three track links, about forty centimetres, and on 13 April 1917 a quick commencement of production was envisaged. In reality Estienne had already on 22 March decided to discontinue this project in favour of a Renault FT command (signal) version. The CA2 prototype was subsequently used as a training and test bed vehicle and the immediate need for command vehicles was met by fitting two standard Schneider CAs with radio sets. On 29 December 1916 it was proposed to develop from the Schneider CA2 two light tank prototypes. Early 1917 it was suggested to construct some vehicles as flamethrower tanks by installing a flamethrowing device in two armoured turrets, one at the left front corner and the other at the right rear corner, each having a field of fire of about 180°. The fuel reservoirs would be inside the hull. No production resulted. In February 1917, Schneider proposed to build a variant with a thirty two centimetres wider hull fitted in the front with a 47 mm gun and two machine gun turrets placed diagonally behind the driver position, while the engine was relocated to the rear of the vehicle. On 2 April 1917 the Ministry of Armament asked Schneider to design two improved versions of the Schneider CA: one with a gun turret, the calibre not surpassing 47 mm if it were a long gun; the other with a long 75 mm gun in the front of the hull. After the failure of the Nivelle Offensive, Schneider understood that more capable designs had to be manufactured if the tank were to remain a viable weapon system. On 1 May 1917 it discussed a range of possible options, numbered one to five. All had in common that basically the same mechanical components were used as with the Schneider CA, though often improved, and that the suspension was only partially changed: elongated by the addition of an eighth road wheel and using thirty five instead of thirty three wider, forty five centimetres broad, track links. However, all were also significantly modernised: the hull overhang had disappeared, the hull front formed as a sloped wedge, and the inner space was compartmentalised, with an engine room, protruding behind the sprocket, at the back and the driver in front. The armour base was about sixteen to twenty millimetres. The first two proposals were probably identical to the April 1917 projects and discarded by the company as inferior. The last three, favoured by Schneider itself, were all turreted vehicles: design No 3 had a 47 mm gun in the hull and a single machine gun turret; No 4 differed in having two machine gun turrets and No 5 in having the gun moved to a turret. During discussions about these proposals, Estienne pointed out that the intended long 47 mm gun had not entered production yet and that no high performance explosive charge was available to give it a sufficient effect on soft targets. Therefore, he insisted on fitting the standard 75 mm field gun, even if this would raise weight to 14.5 tonnes. A week later Schneider presented proposal No 6, which envisaged a vehicle weighing fourteen tonnes and having a shortened 75 mm gun in the turret. On 5 July 1917 drawings were ready of the type, which was now called the Schneider CA3. However, these included an alternative version with a shortened 75 mm gun in the hull. Estienne had misgivings about this project, questioning its trench crossing capacity and predicting engine power would be insufficient, given a weight that had by now reached 16.6 tonnes. Also he demanded a gun sight allowing some fire on the move capability. Nevertheless, on 24 July the Consultative Committee of the Artillerie Spéciale decided that the four hundred vehicles of the Schneider Modèle 1917 ordered on 10 May 1917, were to be of the CA3 type. These had to be delivered from May 1918 onwards. A prototype was ordered of each version — the mechanical parts in May and the armour hulls in July — but the company itself limited its construction activities to the one with the gun in the hull, probably because a cannon turret was judged to be "absurd" given the lack of enemy tanks and a machine gun turret was seen as necessary for close defence against infantry assault. Later that year, in an official answer to an inquiry by parliamentarian Paul Doumer regarding the progress achieved within French tank development, the designation "Schneider CA4" is used to indicate a design studied within the context of a larger order for two prototypes, weighing twenty tonnes and fitted with a cannon turret armed with the shortened 75 mm gun, and of which Schneider is unable to predict when the single prototype to be constructed would be finished, though deliveries could start in April 1918. A mock up was built of the Schneider CA3, and on 24 October the chassis was tested at SOMUA. During the summer however, Estienne and Pétain had become worried that the medium tank production might become an obstacle to the planned light tank mass production of the Renault FT. On 27 October the committee advised that the construction of the Schneider CA3 would be suspended in favour of light tank production. It argued that the type could probably not be delivered before August 1918 anyway, too late for the summer offensives of that year, and that an improved medium tank design should be taken into development instead. The ultimate decision not to produce the Schneider CA3 was only taken in February 1918. On 19 January 1918 it was proposed that the preproduced CA3 components would be used to construct a further two hundred Schneider artillery tractors. On 3 November 1917 the order for the Schneider CA4 prototype was annulled. The new medium tank project had already been started on 15 August 1917 and strived for a technically advanced seventeen tonne vehicle armed with a shortened 75 mm gun and benefiting from a much improved mobility. It remained a paper project. Sometimes projects of a more general investigative nature considered to employ Schneider CA hulls. In January 1917, engineer Louis Boirault proposed an articulated tank, a vehicle that would be long enough to cross wide trenches and yet sufficiently flexible to maintain mobility. Older literature sometimes suggested that he actually coupled two Schneiders rear to rear to research this concept. In fact, this was on 8 May 1917 merely advised by the committee judging the merits of the proposal, as a lighter alternative for Boirault's original plans which envisaged three hulls of a completely new design. The Schneider company would subsequently refuse to make any vehicles available and the project was continued based on the Saint Chamond hull.

Even before the end of the war, on 6 October 1918 Estienne had proposed to phase out all Schneider tanks from operational units, remove their armament and deploy them as instruction and recovery vehicles. These should be distinguished from those vehicles that from the very beginning had been used as supply tanks, with the cannon removed and the hole plated over. Indeed, by the end of 1918, all surviving Schneider tanks had been given the destination of utility vehicles, although it is unknown to what extent and at what rate any rebuilding took place. On 1 December 1918 Groupements I and IV fused with Renault FT units and Groupement II and III, together with AS 9 from Groupement I, reformed into three new Groupements Lourds (I, II and III) equipped with the British Mark V* type. Some of the still serviceable Schneiders were rebuilt as recovery vehicles and tank transporters serving with Renault FT units. In 1928 a project was presented for a Schneider CA Modèle 1928 recovery tank with the upper hull replaced by a motorised crane, that could be stabilised by a large jack at the rear of the vehicle.

The only surviving exemplar of the Schneider CA, at the Musée des Blindés in Saumur, is also the world's oldest tank in full running condition. It was donated at the end of the war by the French government to the United States of America, was preserved in the Aberdeen Proving Ground Ordnance Museum in Maryland, USA and in 1985 again donated to France for restoration. The tank's original four cylinder Schneider gasoline engine and the original transmissions were fully restored to original working condition by the repair teams at the Musée des Blindés. This particular vehicle had been fitted with later upgrades, such as the fuel reservoirs located at its rear.

The last surviving example of the artillery tractor variant of this vehicle is currently in the possession of the France 40 Association.

Italy in the summer of 1918 formed its first tank unit, the Reparto speciale di marcia carri d'assalto, with one Schneider and three Renault FT tanks; the Schneider tank was replaced in November 1918 with a FIAT 2000.

On one occasion after the war phased out Schneider tanks were exported. After an urgent request by the Spanish government following serious defeats against Berber rebels in the Rif War, six were sold to Spain on 16 September 1921 within the context of a joint French–Spanish effort to subdue the newly independent Rif Republic. The vehicles were designated Carro de Asalto Schneider M16 and modified by the addition of a driver's visor annex gun port in the front glacis plate. They reached Morocco on 28 February 1922. On 14 March 1922, as the first Spanish tanks to see combat action ever, they provided close support fire. Seen primarily as mobile artillery, they were combined into an artillery assault battery commanded by Captain Carlos Ruiz de Toledo which supported the single Renault FT company. In September 1925 they took part in the major amphibious landings in the bay of Al Hoceima. The Schneider tanks saw action until May 1926 and returned to Spain in 1929, not having lost a single vehicle. In Spain, due to their poor mechanical state, they were delegated to a reserve status and used as training and instruction vehicles. Four were part of the depot of the Regimiento Ligero de Carros de Combate N° 1 at Madrid, a Renault FT unit, the other two were part of the depot strength of RLCC N° 2 at Zaragoza, the other Renault FT unit. At the outbreak of the Spanish Civil War, the first unit remained under Republican command, while the second took the side of the Nationalist rebels. The Madrid vehicles saw some action during the bloody attacks on the Cuartel de la Montaña, the main military barracks of the capital. Some of the tanks were manned by militia members of the Unión General de Trabajadores and the Unión de Hermanos Proletarios. Also the Zaragoza vehicles participated in the initial fighting. Probably all Schneider tanks became inoperational during 1936.

According to an English military observer named Impey, the Fengtian Army had a number of Schneider tanks by 1925.